Electrocoin cab questions

Kewydee

Active member
Credits
221CR
Hey guys, does anyone have a link to the pdf manual for an Electrocoin Spectrum Deluxe cab?

And is the Electrocoin wiring the same as Jamma? Ive seen an Electrocoin to Jamma adapter for sale which makes me wonder whats what?

Does this cab need this adapter to work on jamma pcb's?

Cheers.
 

Fuzzy

Active member
vacBacker
Feedback
18 (100%)
Credits
564CR
Kewydee said:
Hey guys, does anyone have a link to the pdf manual for an Electrocoin Spectrum Deluxe cab?

And is the Electrocoin wiring the same as Jamma? Ive seen an Electrocoin to Jamma adapter for sale which makes me wonder whats what?

Does this cab need this adapter to work on jamma pcb's?

Cheers.

The Unigame (Electrocoin) pinout is slightly different to JAMMA so you will need a Unigame-JAMMA adaptor to play JAMMA PCBs.

These are fairly common and easy to get hold of for around £15.

Having said that, some Electrocoin cabs were JAMMA wired, so check first!
smiley1.gif
 

Kewydee

Active member
Credits
221CR
Thanks for the advice guys - nice one

Any idea where i can find the cabinet manual online?

What is the little board fixed to the left side of the bottom section - it has 6 green little knobs on it, what do they adjust?

Not having any cab experience and no manual makes finding out things hard - I am glad you guys are here and are kind enough to share your know how.

Cheers
smiley20.gif
 

Fuzzy

Active member
vacBacker
Feedback
18 (100%)
Credits
564CR
Kewydee said:
Thanks for the advice guys - nice one

Any idea where i can find the cabinet manual online?

What is the little board fixed to the left side of the bottom section - it has 6 green little knobs on it, what do they adjust?

Not having any cab experience and no manual makes finding out things hard - I am glad you guys are here and are kind enough to share your know how.

Cheers
smiley20.gif

I'd be surprised if there was a manual as such, as it's pretty much a generic cab. If you can identify the monitor, you will be able to find a manual for that.

The board you mention sounds like a remote board for adjusting the monitor - very handy as this saves you going round the back of the monitor and poking about!
smiley17.gif
 

Kewydee

Active member
Credits
221CR
Another question for you guys.

The picture on my screen is slightly too large for it to be all shown, it cuts off the hi scores halfway though the numbers and the credit at the bottom is also only half showing on some games

What should i adjust to squeeze the screen so it is slightly smaller and fits without cutting anything off?

I am using a 60 in 1 pcb on a spectrum cab

Cheers
 

obcd

Active member
Credits
3,830CR
If the monitor is positionned normally (larger than higher like a TV), you need to adjust the vertical size potmeter. You might need to adjust the vertical linarity as well. (If it's only the upper or lower half that is 2 large) If your monitor is rotated (bigger size from top to bottom), you will need to find the horizontal size and linearity.
 

Kewydee

Active member
Credits
221CR
Should clarify a bit

Vertical monitor - picture is too large at top and bottom both at same time

Also its a bit off towards the left, but i have already adjusted the picture as far right as the pot would go

Need to shrink the picture so i can get it centred nicely.

Is that type of adjustment on the little board with the green knobs? (on the inside left of the cab, where the pcb goes)

I have no service manual and its hard to see inside to cab, my eyes are not good enough to read the tiny writing on the base of the pots.

Cheers for sharing your know-how
smiley20.gif


Low tech noob here, simple laymans language pleaseKewydee2014-11-25 16:09:38
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
You need to find the horizontal width coil or adjust pot, it will depend on the type of monitor on that cab. If its a 25in monitor vertically mounted it is likely to be a Hantarex 9110 or Polo 2 which usually have a remote board - although sometimes there's a failed bipolar cap down near the flyback (on the 9110 model) that will prevent the width from being user controlled much.

I haven't seen an Electrocoin manual for a Spectrum but they are really easy to understand.

Yes, the board inside the PCB area is usually the monitor adjustment board on that type of machine.

Get a decent torch and your camera phone and take a picture and then zoom in. You can usually lift the adjustment board out of a holder so that you can access it better but sometimes they are completely fixed down.

Its hard to say whether it would have been JAMMA by default, only looking at the connector and doing a bit of assessment on the wiring would figure that out but I think Electrocoin stuck to UNIGAME pinout right the way through - some were rewired by operators.

UNIGAME came before JAMMA and was a way of making a cab interface that was uniform - its seen as early as the Goliath Mk1 and i've experienced it in a lot of DECO cabs too.

Given a few cabs i've picked up, i've had a unigame fingerboard with wires hanging off it, I think the idea was they'd supply this to you with the machine but with no edge connector for the game board, the arcade operator would solder on the necessary connectors to interface the game board to the cab - some games needing extra connectors on other parts of the board and maybe a 44 pin edge connector.

Sadly a lot of operators just soldered wires to the PCB - but back then you couldn't blame them, a game lived in a cab for at least a year and sometimes longer. I've also picked up cabs where the board is still in - screwed to the side of the cab and with the wiring soldered direct to the cab.

RGP2014-11-27 00:08:22
 

Kewydee

Active member
Credits
221CR
Thanks for all your help and advice

I found the monitor manual online and discovered which pots were the right ones to adjust the screen on the remote board

It seems that Horiz Amp pot is Horiz Width

Vert Amp pot is Vert Height

It was not immediatly obvious what pot did what but the manual showed that the remote board has italian / english descriptions which caused the confusion.

Cheers
smiley20.gif
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
And of course, if the monitor is rotated, the controls are backwards in appearance, the top-bottom of the screen is the horizontal and the left/right of the screen is the vertical controls.

You wouldn't believe how many time I have to explain that to a friend of mine.
smiley4.gif
 
Top