Fluorescent rebuild help

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
Just out of interest, why not stranded? I'm thinking the current capability of solid core would be slightly more than stranded, and I'm not sure if there is an EMI risk with multi-core if you're sticking high frequency AC through it, but nothing I can think of that makes me think "defo solid core".

Purity - once you've got all this figured out, a short write-up to go as a sticky would be very cool :) Flouro lighting, ballasts and starters seem to be an FAQ so if you wouldn't mind summarising your findings we'd appreciate it!
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
trmatthe said:
Just out of interest, why not stranded? I'm thinking the current capability of solid core would be slightly more than stranded, and I'm not sure if there is an EMI risk with multi-core if you're sticking high frequency AC through it, but nothing I can think of that makes me think "defo solid core".

Purity - once you've got all this figured out, a short write-up to go as a sticky would be very cool :) Flouro lighting, ballasts and starters seem to be an FAQ so if you wouldn't mind summarising your findings we'd appreciate it!

It's simply down to the connector type. There are small holes either side that are too small and difficult to get stranded wire in, although I'm sure it's possible.

I did try using stranded cable on one of the holes and it didn't fit or retain the wire particularly well (hence my post). So I took andy's advice and used solid core which meant it was dead easy to fit and the cable locks solid onto the ballast.
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
So, I accidentally started a similar 120v 50Hz thread under general a few days back... if anyone has found a source for these yet or wants to do a bulk order LMK. In the meantime I just found this FAQ which explains pretty much all you could want to know about tubes...

http://members.misty.com/don/f-lamp.html
karlcdoe2010-08-11 17:40:55
 

andyman

always pull away from your face
Credits
1,059CR
Its not the size of the holes, its the way the connectors grip the cable, doesn't work with stranded.

Andy.
 

chadsarcade

Lord of Vectors (tm)
Feedback
11 (100%)
Credits
443CR
andyman said:
Its not the size of the holes, its the way the connectors grip the cable, doesn't work with stranded.

Andy.

I was taught that is was good practice to tin the ends of stranded wires, doing so would likely make stranded perfectly acceptable for this situation.
 

andyman

always pull away from your face
Credits
1,059CR
chadsarcade said:
andyman said:
Its not the size of the holes, its the way the connectors grip the cable, doesn't work with stranded.

Andy.

I was taught that is was good practice to tin the ends of stranded wires, doing so would likely make stranded perfectly acceptable for this situation.

Yeah, I suppose that would work if your tinning technique was 100% every time. Holes don't allow for much tolerance. Always just used solid core as that was supplied (used to work fitting fluorescent back boxes for signs) so accepted as standard.

Andy.
 

g00n3r

Arsenal till I die
Credits
48CR
It's been an issue for years (50/60hz difference causing chokes to burn out).

I usually just take a 220v feed and fit a UK choke, but have on many occasions used a 110v Stern pinball choke .

These are good too (220v though) here
g00n3r2010-08-11 22:32:46
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Tested the Fluorescent rebuild before with the ballast from Rav and it works fine
smiley20.gif
 
Top