Ghosts N Goblins Bootleg help

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
Have you had any signs of life since you reprogrammed the ROMs? Do you still get overheating on the CPU when it's plugged in? Do the new EPROMs get hot too?

Cheers
tim
 

cathaldub

User
Credits
46CR
Hey Tim
The new EPROMs stay nice and cool, board boots.
Having a slight problem, can be seen in my video below
Not sure if it's a problem with one of the EPROMs on the second board which I haven't replaced or with the ram
What do you think? The board is visibly mint with no broken traces, etc.
The sound amp is removed at the moment as the old one was dead.
http://www.youtube.com/watch?v=WLXa3lGO0SQcathaldub2012-02-04 00:07:07
 

VectorGlow

Active member
vacBacker
Feedback
34 (100%)
Credits
900CR
Just checking through my Ghosts 'n' Goblins repair log, i've documented some vaguely similar faults which may give you pointers on where to look. Here goes:

Symptom: All sprites VERY broken up and partly ‘scattered’
Cure: Bad 2114 at location 11E on video board – replaced

Symptom: Top halves of all sprites apparently missing, but on closer inspection it appeared that anything that entered the horizontal plane (head height within the game) then briefly disappeared – video board fault
Cure: Pin 14 of the LS175 at location 8E was stuck low – replaced IC

Symptom: Sprites have chunks missing from them of varying shapes and sizes – top board fault
Cure: Slightly corroded legs on PROM at location 2E – cleaned off corrosion

I'd start with the 2114 RAMs if I were you.
 

cathaldub

User
Credits
46CR
Just went back to this tonight and I'm getting so close, I piggy backed 2 new 2114 ram chips and it seemed to help so I've Replaced them and it's fixed my graphic problems but I still have no sound, the op amp was burnt and I replaced it but still no joy.
There are 2 ym2203c chips on the board that get very hot extremely fast(straight away) like the eproms did originally, I'm assuming this isn't normal but I dont want to spend an hour taking them out to find out that they were OK.
I've a logic probe there but I'm not really sure what I should be looking for, has anyone any ideas?
 

Zabanitu

User
Credits
330CR
Hi. Ym2203 can get quite hot wich is normal. You need an oscope or an external audio amplifier to test the power amp ic. 2nd thing to check are ym3014 wich are the d/a converter betweeen yamaha chips an pow amp. Also the lm324 wich feeds voltage and preamps the 3014s is worth a look.

In short words... Pe patient or seek support from neighbouring experts.

Regards
 

retrorepair

Active member
vacBacker
Feedback
26 (93%)
Credits
378CR
Check the input to the lm324 on pin 3 (might be 2, pretty sure it's 3 though).

If you can hear audio through your probe (if it has a buzzer) you know anything past that is good but check it's at least high. If it's low the IC has probably kicked the bucket. If it's high and there is no audio something before it isn't doing it's job.

You want to make sure your sound rom is being addressed and read out properly though. Grab a pinout and make sure all the address and data lines are singing. If one looks bad, trace it back to the component it's attached to.

It's rare for a YM to go bad in my experience. If the amp shorted I'd look at anything attached directly to that or using 12v.

My money is on that lm324 anyway.
 

cathaldub

User
Credits
46CR
Thanks
There is no buzzer on my probe
smiley36.gif


I've tested all 14 pins with the logic probe and here are the results
pin 1-7,12 give no reading at all
pin 8,9,10,13,14 are high
pin 11 is low
So I'm guessing there is something wrong before this chip as I should have a reading on the first 2 inputs?

cathaldub2012-07-14 18:40:59
 
Top