Konami customs

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Just trying to work out what some of the chips are on a Mikie PCB if anyone can assist?

I think I've worked out most of them but just unsure about a couple.

So what I think I know so far is:

9A = 6809 CPU
5C & 6C = 76489AN Sound chip
4E = z80
10F = 5533 (4k 8bit static ram) - similar to the TC5533P
12H, 1I, 2I, 3I, F9 = labelled as J349X which I think is a 6301 Prom
A14 = 2128 Static Ram

What I don't know about is:

7E = labelled as "2009". This is a 24 pin chip
C15 = labelled as "085". This is a 28 pin chip

Any thoughts?
 

cmonkey

Active member
vacBacker
Feedback
4 (100%)
Credits
1,659CR
Correct on all counts Ben.

The 2009 is probably just a 2128 ram with only 10 of the 11 address lines utilised. A10 (pin 19) seems to go to a jumper (jp 4??) which either ties it high or low (depending on position of said jumper). If A10 is high then the upper 1024 bits of the ram will be used, if low then the lower 1024 bits of the ram will be used.

The custom 085 is a Konami black box, but I believe it's a sprite related custom.
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Thanks Adrian that's really helpful.

I'm just trying to work on the board at the moment. This is what I have so far.


I'm trying to understand what everything is on the PCB so your confirmation is good :)

Initially the board didn't boot, and was shutting my power supply down. I found that someone had tied what on my adaptor was the -5 and +12 lines together on the PCB, so was causing my power supply to short. I've undone that and now the board boots as above.

I was worried that this had fried some chips, but the pinouts I've come across seem to indicate the -5 is actually not connected so I don't think the -12 would have done any damage.

So this is where I am now. I think the z80 is ok because I think this is controlling the sound, and that seems ok.

I've checked the roms and they all ident ok and are in the correct positions compared to the mame rom "mikehs"

I need to check the ram, particular on the gfx lower board. I want to see if I can see any issues with the MBM2148L-55 @H12 and H11.

The only problem is I'll need to separate the boards so I'll need to extend the bridge between the top boards so I can lay it out
Purity2014-07-05 20:54:11
 

cmonkey

Active member
vacBacker
Feedback
4 (100%)
Credits
1,659CR
Can you get into the service menu? Hold down P1 Start and P2 Start whilst the board is booting to get into the service menu. Then press P1 Start to cycle through the different service menu screens.

Although to me it looks like the text ram part of the board isn't working so I don't think getting into the service menu will do a lot of good anyway!
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Nope, I tried earlier on today to get into the test menu, before posting on here

I think it does actually go into the test menu, but the graphics are the same so I can't see anything anyway
Purity2014-07-06 00:21:07
 

caius

Active member
Feedback
7 (100%)
Credits
588CR
Your issue could depend from a bad video timing circuit.Are there on the PCB counter ICs like 74LS161/163?

caius2014-07-11 06:49:45
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
caius said:
Your issue could depend from a bad video timing circuit.Are there on the PCB counter ICs like 74LS161/63?

Yup

74LS161

@B7, @B3, @B2, @F13

74LS63, did you mean 74LS163?

If so there are quite a few:

@A11, @A12

@B11, @B12

@E11, @E12

@F11, @F13
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
From the testing that I did I found that the 161/163's looked ok.

I've finally made some progress with this
smiley1.gif


I found a broken 74LS373 at A8 on the bottom GFX board and this has corrected the screen.

I'm getting there :)

 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Another day and another broken 74LS373!

But this time at C6.

I can now see the character sprites better, but have noticed that Mikie has half his body upside down! Same with the teacher

Also I think you can now see the component parts of the Mikie logo at the start, but jumbled around?? Also the teacher makes an appearance on the logo in several places

Clearly still some problems with the board but making progress!

Purity2014-09-14 21:05:49
 
Top