Mame cab creation?

retroshaun

Active member
Feedback
1 (100%)
Credits
54CR
[ukvac] Mame cab creation?
Hi guys,
Been thinking of converting a crappy, unused table into a Mame cab and now I have the relevant PC parts going spare, it may be time. As I have no idea how to do this... a few basic questions for you all...

1) Will a PC power supply be sufficient to power the PC parts and the monitor also (assuming I'm using the original arcade monitor)? If so, how do I attach the monitor to the PC power?

2) How do I connect up the outputs of the video card and sound to the wiring in the cab? IE do I make some kind of finger board to simply plug into the original wiring or is this a bad way to do it?

3) How do I connect controls up to (I presume) a PC keyboard to simulate mame keyboard clicks or is it better to connect it all up to the PC joystick port?

Thanks guys
Shaun
 

pobtastic

Moderator
Staff member
vacBacker
Feedback
2 (100%)
Credits
477CR
RE: [ukvac] Mame cab creation?
>1) Will a PC power supply be sufficient to power the PC parts and the
monitor also (assuming I'm >using the original arcade monitor)? If so, how
do I attach the monitor to the PC power?

A PC power supply is DC and will only power the PC... The monitor requires
an isolated power supply, hooking it up to the mains will damage it
drastically!!! Most tables have a power supply AND an isolated power
supply, just leave it in there!

>2) How do I connect up the outputs of the video card and sound to the
wiring in the cab? IE do I >make some kind of finger board to simply plug
into the original wiring or is this a bad way to >do it?

Don't bother messing around, buy a J-Pac... Its too cheap to bother making
your own and worrying about stupid stuff like keyboard ghosting. It
amplifies the video AND sound too, check out their website:
http://www.ultimarc.com/

>3) How do I connect controls up to (I presume) a PC keyboard to simulate
mame keyboard clicks or >is it better to connect it all up to the PC
joystick port?

Ditto, number 2...

Pobster
 

John Bennett

Senior Member
vacBacker
Feedback
10 (100%)
Credits
5,325CR
RE: [ukvac] Mame cab creation?
When you say 'the original arcade monitor', have you got an old JAMMA
cabinet you're thinking of plundering? If so, then all three are easy - the
cabinet PSU takes care of the monitor, and use a J-PAC
(http://www.ultimarc.com) for points 2) and 3) J-PAC routes button and
joystick signals through the firmware and converts to configurable keyboard
presses.

HTH,
nutts



DATA Imported from archives: originally posted by Andy Nuttall (ANuttall@Channel4.co.uk)
 

retroshaun

Active member
Feedback
1 (100%)
Credits
54CR
Re: [ukvac] Mame cab creation?
Thanks for the help everyone.
I only had a very brief look at J-Pac but it looks the business. So am I right in assuming it controls input (controls) and video also?

Well the cab is a non jamma cocktail so I would, I guess, have to Jammatize it first.

Shame about the power supply though as the one in there at the moment makes one hell of a noise (a sort of rattling, whirring noise) and I was hoping to replace it completely. Any thoughts?

So assuming I stick to the cockatil PS, can I power the PC board from this also?

Shaun
 

John Bennett

Senior Member
vacBacker
Feedback
10 (100%)
Credits
5,325CR
RE: [ukvac] Mame cab creation?
Ah, me being thick - of course you meant a cocktail table. Don't mind me -
listen to pobster :)

If the table's not JAMMA, then an I-PAC will do you just as well, except
you'll have to route the harness yourself.

n



DATA Imported from archives: originally posted by Andy Nuttall (ANuttall@Channel4.co.uk)
 

pobtastic

Moderator
Staff member
vacBacker
Feedback
2 (100%)
Credits
477CR
RE: [ukvac] Mame cab creation?
Hey Shaun

Yeah J-Pac does the works, its a very cool piece of kit! The only problem
you may have is whether your video card can output at 15hz or not. There
are links from their site regarding compatibility, check it out :eek:)

On JAMMAtising, yes you would have to do that. But I think you're getting
confused with this whole power supply thing. There are TWO blocks/
transformer windings inside *most* cabs, one supplies the monitor and is the
isolated one, the other supplies the game board with its voltages. Note
that this is not always the case though... Your cab may have an isolation
transformer and a switchmode PSU, or even have a monitor which can be
powered by the mains. You cannot power a PC from a regular switchmode PSU
as it needs 3.3v (I could be wrong on this...) what you need to do is follow
the wiring from the monitor to the power supply area and check out what
happens with it. Ideally you should leave the isolated PSU in there and
remove the other PSU and replace it with an ATX one or something.

Hope this helps! If anything above is wrong am sure someone will correct
me!

Pobster
 

retroshaun

Active member
Feedback
1 (100%)
Credits
54CR
Re: [ukvac] Mame cab creation?
Ah OK now I see what you mean... sorta! I am not too familiar with cocktails and really not too electronically minded either... something I must find time to learn though - where do all the hours go? The Randy Fromm class is seriously tempting.

Anyway. The cab is actually an old Taito cocktail and (tho I cant check as its not at my present location) I think its all totally original. Dunno what TYPE of Taito tho - certainly not a SI as the CP is completely different. So this will have both types of supply right? And if I remove the switchmode PSU and then add a PC PS, will I be able to somehow patch this into the wiring or will it need to be completely separate (ie require 2 mains cables)?

I guess all I need now is to find out what the hell the game was and then work out how to Jammatize it!

But thats a topic for a different email methinks :)

Cheers Pob !
Shaun
 
Top