Pacman ROMs

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Could someone help me please? I am trying to burn some new roms for my Pacman board but am running into difficulties with the data - not sure what is going on. The PROMs should be 2532 and I also have another board containing replacement EPROMs which are also 2532 designation. The data on the PROMs won't work once transferred to new 2532 EPROMs, but the data on the other board set containing EPROMs transfers the data fine. The data on the PROMs and EPROMs isn't the same either.

I'm not sure why this could be? Am I missing something (apart from the data)? Any help greatly appreciated - particularly the data on chips 6E, 5E & 5F that will work on an EPROM.

Another odd occurrence is that when I read the EPROM data of 6E it reads fine. However, the saved data won't verify against the data I just read from the chip. The chip works absolutely fine in the board though. There are definitely more than 4 ghosts in this game.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Can we get some information on the PCBs? Are they genuine for instance or bootleg? Are they both identical? There are many, many variants of Pacman board out there.

Is the board you're trying to burn new ROMs for known to be 100% working or could this just be another fault manifesting itself (i.e., why burning the new ROMs in the first place?)

Have you tried to verify the ROM data that you have read off against mame? And finally do you know for sure that you ROM burner can burn 2532's - they are a bit notorious for having patchy support in programmers.

It sounds like your burner may be struggling with the 2532's, or that the 2532's are just getting to the end of their life, or in some other way damaged if what you've just written to a chip won't then verify.

Are you able to fully erase the chip(s) and then blank check them OK?
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
guddler said:
Can we get some information on the PCBs? Are they genuine for instance or bootleg? Are they both identical? There are many, many variants of Pacman board out there.

Is the board you're trying to burn new ROMs for known to be 100% working or could this just be another fault manifesting itself (i.e., why burning the new ROMs in the first place?)

Have you tried to verify the ROM data that you have read off against mame? And finally do you know for sure that you ROM burner can burn 2532's - they are a bit notorious for having patchy support in programmers.

It sounds like your burner may be struggling with the 2532's, or that the 2532's are just getting to the end of their life, or in some other way damaged if what you've just written to a chip won't then verify.

Are you able to fully erase the chip(s) and then blank check them OK?

Ok, didn't realise I needed to include everything but much appreciated for replying.

The boards are Midway original and appear identical. I bought some a while ago to repair and have just got round to fixing them - most were unpopulated with ROMs so I've been swapping sets out to repair them and am now trying to obtain a duplicate set for the unpopulated board.

I've bought several 2532 EPROMs and own an Exeltec 280U which has burned the chips at 6F, 6H & 6G fine with data from EPROMs with Midway labels on them.

The PROMs are identified with numbers only. When I try to copy the data from the PROMs onto the EPROMs there are errors on boot. The 5E & 5F chips are missing from my MAME version of Pacman - I can't seem to locate them. I don't keep up to date with MAME at all.

So, I have successfully copied 6F, 6H & 6G from data contained on EPROMs but can't do the same with data from the PROMs. I can erase and program the EPROMs no problem. I have about 20 2532's of different type - just bought them.

Is there anything I've missed?
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Yeah, it could be this...

I had the same problem on a Gorf the other day when reading 9332 PROMs. Assuming it is the same proms you need to swap pins 18 & 21 (using an adapter or something) to be able to read them properly as 2732's.

http://www.ukvac.com/forum/reading-9332a-roms-gorf_topic342675.html

Other than that, it sounds like you have the basics covered so the only other thing I can really offer is that I have the mame images if you wanted them?

guddler2015-01-31 15:41:00
 

RaveN

Active member
vacBacker
Feedback
1 (100%)
Credits
1,325CR
" The 5E & 5F chips are missing from my MAME version of Pacman - I can't seem to locate them"

Midway's Pacman is a "romof" "puckman" in mame, ie Mame classes the Japanese version "puckman" as the parent. If your romset is a merged set, zip files of games are missing roms that are identical to the parent (to save storage space).

You just need to find a pacman.zip from a split romset.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Thanks for the replies - can I post a photograph later to confirm the designation of the PROM? Then I will absolutely know what to do with it. I can build something from a couple of sockets to swap the pins over - thanks.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Ok, had a look at the PROMs and they are 9332B.

I've verified the ROMs contained in my MAME set (pacman) and 6F and 6H are a match to the EPROMs on my board. 6E & 6J do not match. When I burn the complete set along line 6 (E to J) from MAME and place them in my board it won't boot - I get flashing numbers on the screen (similar effect to the custom at 6D packing up).

I have a spare 6H PROM, so I'll build an adapter (identical to the one used on 9332A) and see if I get anywhere.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Ok, built the stack of 24 sockets and swapped pin 18 to 21 and pin 21 to pin 18. It unfortunately hasn't worked
smiley19.gif
.

I have downloaded the data as a 2732 and then programmed it to a 2532. The data matches exactly as if I had downloaded the 9332B as a 2532, what I originally did.

Is 9332A the same as 9332B? That's the only thing left, I think?
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
2732 and 2532 are not the same thing. Myself and Nad were talking about the exact same thing yesterday
Purity2015-02-01 15:09:38
 

favouredson

Super Star
vacBacker
Credits
1,260CR
jonhughes said:
Ok, built the stack of 24 sockets and swapped pin 18 to 21 and pin 21 to pin 18. It unfortunately hasn't worked
smiley19.gif
.

The pins are not a direct swap between the two types.

Pin 2732 2532

18 CE A11

20 VPP CE

21 A11 VPP
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
favouredson said:
jonhughes said:
Ok, built the stack of 24 sockets and swapped pin 18 to 21 and pin 21 to pin 18. It unfortunately hasn't worked
smiley19.gif
.

 

The pins are not a direct swap between the two types.

Pin 2732 2532  

 18 CE A11

 20 VPP CE

 21 A11 VPP

Ok, I hadn't looked at the pin-outs and just relied on the posted information. There is a bit more to it then.

What is confusing me the most, right about now, is if the 9332B pin-out is different from a 2532 why is the board recognising both chips in the same socket and running with no problems?
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Ok, here are the 2 chip sets I currently have.

WP_20150201_001.jpg


I can copy the data on 6F, 6H & 6J. 6E is a total pain - the reader will read the data but can't verify the information from the chip (6E) it has just read from.

WP_20150201_002.jpg


This is my other set. I can interchange any chip and they all work in any board set. But download these 9332B PROMs as 2352s and they won't work when burnt to an actual 2352 chip.jonhughes2015-02-01 17:19:27
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Are you simply trying to burn a set of 2532 ROMs using ROM images from MAME?

That's what I'm trying to do at the moment, but programmer is not playing ball at the moment with any of the ROMs I have. Not even attempting to Program them.

Not sure why yet.

What brand of 2532s are you trying to Program?

Are you sure the problems are not related to a specific brand of EPROM? Like the TMS2532?Equites2015-02-01 17:51:45
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
I've sorted this now. I found 5E and 6E from a board set in my loft and Martin kindly donated the ROM files from MAME and 5F seems to be accepted by the board from what he supplied.

I'm still foxed at why I had the problems but glad it's sorted now, thanks to you all.
 

jonhughes

Active member
vacBacker
Feedback
52 (100%)
Credits
1,156CR
Equites said:
Are you simply trying to burn a set of 2532 ROMs using ROM images from MAME?

That's what I'm trying to do at the moment, but programmer is not playing ball at the moment with any of the ROMs I have. Not even attempting to Program them.

Not sure why yet.

What brand of 2532s are you trying to Program?

Are you sure the problems are not related to a specific brand of EPROM? Like the TMS2532?

The ROMs I found for 5E and 6E are both 45 speed. They are all Hitachi 2352 I have burned for the complete set, HN462532G which are all 45 speed. I have taken data from chips off boards with EPROMs installed, the data from my MAME set wasn't working at all and wouldn't verify against most of EPROM data I had.jonhughes2015-02-01 18:49:39
 
Top