Paint or laminate?

Syrup2407

Active member
vacBacker
Feedback
5 (100%)
Credits
163CR
Hi all,

I have a Tehkan Phoenix cab that I am looking to repair. I have just fixed the gameboard and the monitor so it is now time to start on the cabinet.

It appears to have been manufactured with either a very thin laminate on it or a thick coat of paint. I have given one side a good clean but I have no choice but to either fill and re-laminate or fill and then respray.

Having never done anything like this before I am undecided how to proceed. Can anyone give any advice on the best route to take?

Thanks,

Gav

IMG_1952.JPG


IMG_1951.JPG
 

strykr

Active member
vacBacker
Feedback
11 (100%)
Credits
1,351CR
Unless youve got a good spray booth set up Tbh after laminating my last cab i cant see myself painting one again, less prep and sanding flawless results and hard wearing.
 

Syrup2407

Active member
vacBacker
Feedback
5 (100%)
Credits
163CR
Hi Strykr,

Thanks for the tips.

I have watched a few episodes of Johns Arcade and he seems to also be favoring laminate these days.

Can you recommend a UK supplier for laminate (it will need to be pretty thin) and also an adhesive?

I am keen to give laminate a go!

Cheers,

Gav
 

aeroflott

A different league
Feedback
16 (100%)
Credits
1,061CR
Depends what sort of finish you want. There's a lot to be said for rollering paint on if you're not much of a woodworker. It'll never be super smooth, but it's perfectly acceptable I think (I did a Nintendo cab with a small roller - took three coats, but I was happy with it).
 

Mr20to5

Active member
vacBacker
Feedback
1 (100%)
Credits
1,366CR
With time put into the preparation and sanding, a roller will give an amazing finish when done properly. However it's the dust on the air that will kill the finish if you haven't got a paint booth or similar.
 

strykr

Active member
vacBacker
Feedback
11 (100%)
Credits
1,351CR
Ive seen some superb paint jobs on cabs, mine are passable, i just cant be arsed with all the prep and sanding and waiting at the mo,

I ended up getting mine from Formica, whatever there cheapest white was. Was about to buy it from a branch near me then after speaking to purity discovered that the same product from the same seller oop north was 40 quid cheaper!

I think i used evostick contact adhesive last time, brushed it on although ive seen some use rollers. Some long bits of wood, a j roller laminate router and bit. It went pretty well, only advice i would give is to make sure the outline of cabinet is quite good as the laminate router follows its contours so if there are lumps n bumps on the exterior the laminate will match them.
It protrudes from the t molding about a mm or so which isnt ideal but you dont really notice it tbh, the next cab im doing i have ordered wider t molding and am gonna cut it down flush.

Also wear eye protection when your trimming as ita sharp and flies off particularly when you are making the initial cut.
strykr2016-09-04 18:00:10
 

Syrup2407

Active member
vacBacker
Feedback
5 (100%)
Credits
163CR
I have taken a hot air gun to the cab and although it is a little stubborn the paint is coming away fairly easily, its going to take a few hours to get it all off.

I have decided to give laminate a go and see how it goes.

Will keep you posted on progress!

Thanks for all your help.

Gav
 

Syrup2407

Active member
vacBacker
Feedback
5 (100%)
Credits
163CR
Progress update, the stripping has begun.

Am using a hot air gun to soften the paint and a scraper to remove. Progress is not fast (it has taken an hour to remove a third of one side). The wood below the paint looks to be quite solid (so far) I think things will get more interesting the lower down the cab the process progresses....

IMG_1959.JPG
 
Top