Sega Model 1 help

simon_m74

Virtually real!
vacBacker
Credits
357CR
Hi all

I have a Sega Model 1, with Virtua Fighter roms.

Bought from ebay as a 100% guaranteed working, from a seller with high feedback, so I assume sold in honesty.

Thing is, once it arrived from USA, the plastic feet had snapped, and the board has slid around in the case, damaging the connector.

I have repaired the connector installed new feet, and all seems good, mechanically.

When I try to power it up, I get just 4 out of the 5 green LED`s on the main board, powered up, all very dim, and flicking quickly.

Any ideas?

PSU not powerful enough?

Board fault?

Simon
 

thechop

Model 3 Man
Feedback
15 (94%)
Credits
388CR
Do you have an I/O board connected?

Been a while since I tatted with these but I'm sure they won't boot unless an I/O board is present and powered up.
 

simon_m74

Virtually real!
vacBacker
Credits
357CR
Hi

I have an IO board, and all the audio boards too.

The IO board does have a nice bright red LED thats lit when powered, so I assume thats ok.

One thing on the IO though, there is a small connection that has power (yellow and white), one of each on is, that comes from the IO board`s main connector.

I cant see where to plug this.

I will also check the small filter board that is used to connect the IO and power to the Main board assembly, as I noticed late last night that had a crack in it, I guess caused by the transport damage.

Other than that - is there anything else I could check ?
 

simon_m74

Virtually real!
vacBacker
Credits
357CR
So just tonight, I have switched the PSU, that gave out 5v@12a and 5v@3a to a PC, ATX psu, and I get many more lights now. This PSU gives out 5v@16a on all 5v lines.
Out of the 5 green and 5 red on the main board, I get 4 of each well lit.

I have not yet gotten an image from it, but I am really suspecting that the monitor I`m using is not working correctly.

I will be making up a cable tomorrow I hope, to connect the rgb to a TV, or to a rgb to vga connector - like I have on my model 2, Indy 500 cab I built.

I have tried to connect a speaker up to the model 1 Virtua Fighter system, to see if I get any sound, as I thought that may be easier than the video at the moment.

No sound though as of yet. There are LED`s on the amp, and sound boards that are lit ok, but there is also a series on reg,green,red,green,red, that flash on once upon power up.

I did connect a volume control too, still nothing.

I am not sure if the game will kick into any audio though, without pressing any buttons first?

Looking at the wiring diagram, and the physical, to check I have it all correct, I cannot figure out how the IO board and the Audio boards connect with any data - just power.

I cant understand how that, when player 1 for instance, presses button 1 - that as its connected to the IO board - how does the CPU/Game board know and react?

Am I missing connections? although my system is fully connected as the wiring diagram I have.

Any more help will be appreciated.

Thanks
 

simon_m74

Virtually real!
vacBacker
Credits
357CR
Ok..
Tests so far.
Atx powers up the system.
5 green led
1 red
(in the led cluster)
Other leds elsewhere on the main board and io and audio are on.
Rgb to composite system tried.
Nothing on audio or video.

Any suggestions?

Also, another thing...
Odd wiring.
I have followed the wiring diagram in the virtua fighter manual exactly.
But other than power and audio lines, there is nothing connecting (datawise) between the main board, the io board and the audio system. How does the system know what sounds to play, or what buttons are pressed?
The buttons connector the io, but nothing to the main board.

Am I missing something? If so, the manual I have is missing it too!
 
Top