Tech: Power Drift sound problem

matsod

Newbie
Credits
5CR
Hi all, this is my first post here, please be gentle with me
smiley1.gif


i have a strange problem with my Sega Power Drift Upright cabinet and
i hope that someone here knows how I can fix this.
When the game is in attract mode, suddenly an engine sound plays, over
and over again, looping forever.
Depending on which gear that is in, the sound shifts. but still loops
forever.

I can play the game, and i think the looping sound disappears (or
maybe it's hidden under all the other sounds playing), but after the
game, when in game over/attract mode again, the people cheering and
some music is stuck in the loop.

I have made three videos so you can see what it's all about, and I
also try to attach the schematic for the sound if that helps out.

https://www.youtube.com/watch?v=IhgPPB0JPJg
https://www.youtube.com/watch?v=u82RqSRaJeU
https://www.youtube.com/watch?v=YmTscJvO-DA

I tried to measure with my logic probe and found that the pin 13 on the DAC at IC113 pulses in the same tempo as the looping sound. But on IC114 pin 13 i think I just get a flat *beeeep* Is that a clue? Or am I totally lost here?

Forgot to add, when in sound test, all voice samples is working good, it's just the engine sound that loops.

Thanks a lot in advance/Mattias

matsod2013-06-13 09:35:27
 

matsod

Newbie
Credits
5CR
Oh, thanks for your answers!

Do you know if there is there somewhere I could buy those ICs? Or is my board lost forever?
 

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
Hi Matsod,

It depends on how adept you are at soldering. If you've got the tools then you can probably obtain the parts from P-Man above http://www.andysarcade.co.uk or you could see if anybody is currently repairing these. Mark at Retroclinic normally does these but I don't know if he's on temporary hiatus as he's just moved house - http://www.retroclinic.com/. Might be worth mailing him and seeing - he's a member here too.

If you fancy doing it yourself, and you're pretty sure you won't screw it up then post up and we'll try to help.

cheers

tim
 

matsod

Newbie
Credits
5CR
Hi trm! I am quite good at soldering, I have mostly repaired pinball games for like 15 years and sometimes cheated with arcades as well, but I am a little slow on understanding the logics in this case
smiley1.gif


But these things are quite difficult I guess, but when you manage to fix a difficult problem it feels so good inside
smiley1.gif


I got three different solutions for this problem already, I just hope one of them are correct, and hopefully not the custom-IC which seem to be very hard to find.

So right now I'm waiting for the MF6CN-50, DAC and RAMchips to arrive here so I can start to change them and test.

If someone have another idea, please share them with me!
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
Start with the ram. There is nothing wrong with your MF6CN or DAC because you are hearing the samples. What you are hearing is the samples being played at the wrong times, this is a ram or control issue, its not analogue, so stay away from those, save your self potential damage to the pcb and a wild goose chase.

Be aware this is a multi-layer pcb and you need a good soldering iron to desolder the old ram, or even just to remove and clear the holes if you chop the ram out.

It is also worthwhile verifying the sound roms in an eprom reader, thats a low-impact thing you can do as the chips are socketed.

And BTW - the schematic image you linked to is for the music, it not for PCM samples...
 

bbz149

Active member
vacBacker
Feedback
26 (100%)
Credits
1,608CR
Forget getting IC's out of those boards without a De-solder station! and there is no way you will get those chips out with a pump!Hopefully its just a RAM, but if not then the custom sounds forked just like my Super Hang-on i just fixed. Also check all the legs on the 315-5218 to check none have been knocked off

Here is what mine sounded like


And this was the culprit I changed which is easy enough to change if you know what your doing!

20130521_205208_zpsa7241e86.jpg


Before a good clean and replacement installed

20130601_162148_zps20147c61.jpg
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
bbz149 said:
Forget getting IC's out of those boards without a De-solder station! and there is no way you will get those chips out with a pump!

Not true. The secret is in having a good iron. I do not have a de-solder station, i've never found one that is quicker or easier or does as nice a job as my own iron and my trusty solder pump. I'll take any desoldering challenge and show you that with skill nothing is impossible with thru-hole technology. I can remove IC's and make it look like it came out the factory.

These customs don't grow on trees (if you have a source, then say), the OP should try the other methods first before contemplating a hot-air re-work solution for the custom.
 

bbz149

Active member
vacBacker
Feedback
26 (100%)
Credits
1,608CR
P-Man said:
bbz149 said:
Forget getting IC's out of those boards without a De-solder station! and there is no way you will get those chips out with a pump!

Not true. The secret is in having a good iron. I do not have a de-solder station, i've never found one that is quicker or easier or does as nice a job as my own iron and my trusty solder pump. I'll take any desoldering challenge and show you that with skill nothing is impossible with thru-hole technology. I can remove IC's and make it look like it came out the factory.

These customs don't grow on trees (if you have a source, then say), the OP should try the other methods first before contemplating a hot-air re-work solution for the custom.
Cool, I got a good station and ill jack the temp up and try that next time. Also found those customs easy to change without hot air and easy to install with a little liquid flux and an Iron
smiley4.gif
 

matsod

Newbie
Credits
5CR
Just for your info, I desoldered the two ramchips and socketed them, and it wasn't that hard. Now I *really* want the new ones...
smiley1.gif


Otherwise, noone here that want to sell me a roken board so I can take parts from it?
 

matsod

Newbie
Credits
5CR
Wellwell, I finally got my new RAM ICs, and there are still problems. The first is that the samples are played too slow now, is that because the speed of the RAM is too slow?

And the looping is still there so I guess it's the darn custom IC that holds the real problem here.
Now I guess I must start the chase for a new working PCB or one that has a 315-5218 that works.

You don't know where i could get one do you?

Thanks/Mattias
 

Zabanitu

User
Credits
330CR
hi,

i remember about a thread in wich it was discussed something about having slow music/sample playback on a SEGA pcb...

it was related to the clock divider circuitry or the custom pcm ic IIRC...

maybe someone can remember better than me.
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
Its sounding more and more like a bad PCM custom now, which is not surprising, they are a common failure. Unfortunately you will have to get one from another pcb, out run, super hang-on, or another y-board.. not cheap or easy.
 
Top