The things an operator will do for ...

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
... a few inches of PCB edge connector?!

Here's a rather sorry looking Asteroids Deluxe board that some
operator defiled. The diagnostic interface edge connector has been
hacked off. What do you think? Salvageable or is it destined to be
spare parts for my working ones?

These snaps are of the corner near the CPU, there are a fair number
of wires in this area (see the solder side pic).

top.jpg


bot.jpg
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
That's now a parts board :(

We did a raid last year up in Newcastle (NUUUUUUUuuu CASSEEL!) and one engineer guy was chopping all the gold plated JAMMA edge connectors off PCBs and then weighing it in at those 'we buy gold' places.

He did this to about 200-300 JAMMA boards (imagine the time it took!) for £60.

We came along and gave him £5 per PCB (the intact ones, he had dumped the ones he had butchered).

He couldn't believe his luck! And nor could we HAHA
 

Luigi

Active member
vacBacker
Feedback
4 (100%)
Credits
72CR
I cannot believe he destroyed an Asteroids Deluxe-board to get a pcb connector
smiley19.gif


Ol: for they know not what they do
smiley18.gif

Luigi2016-03-30 10:13:46
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
darthsylly said:
Alpha1 said:
He did this to about 200-300 JAMMA boards (imagine the time it took!) for £60.

Tragic. It's the only word for it.
smiley19.gif
Madness! Have they not heard of the internet? Even at a fiver each they would've had a grand for 200! I'll bet there were some really good boards in there as well.
smiley18.gif
Same as on YouTube - I've seen people destroying perfectly good eproms, ic's and the like for a few ounces of gold that isn't worth anything like the chips themselves if they were cleaned up and sold on!
smiley5.gif
tb20002016-03-30 10:48:46
 

grobda

"Look at the size of that thing!"
vacBacker
Feedback
7 (100%)
Credits
1,061CR
I inherited a jamma adaptor where the 'fingerboard' was a hacked off jamma connector.
smiley18.gif


Call me an optimist but I reckon you could salvage that ADX PCB, most the traces gone will be to the connector, doesnt look like theres much else gone on the parts side at least;

http://www.brasington.org/arcade/products/adl/dlx-pcb2.jpg

I can do you a scan of a intact PCB if you want to give it a go.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Alpha1 said:
He did this to about 200-300 JAMMA boards (imagine the time it took!) for £60.
What a waste!

At least the real vintage boards don't have gold edge connectors, but

I bet they still destroyed some classics.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
grobda said:
Call me an optimist but I reckon you could salvage that ADX PCB, most the traces gone will be to the connector, doesnt look like theres much else gone on the parts side at least;

http://www.brasington.org/arcade/products/adl/dlx-pcb2.jpg

I can do you a scan of a intact PCB if you want to give it a go.

Thanks for the kind offer (I have a working board set so shouldn't

need a scan). I have a feeling the board is going to have other

problems too (or it may not have been on his scrap pile).
 
Top