1982 Atari Battlezone vector issue...

kevwolf69

Newbie
Credits
52CR
So I've had this machine for around 5 year and in that time it has been rock solid. I initially did a cosmetic and board refurb. New interconnect cable. Reflowed all headers. New big blue. Recapped the ARII board. Installed the relevant components to give more control over the screen setup. At the time I had a thread going on here after I managed to create a short in the ARII board resulting in a blown 5v reg and no sound. All fixed with the help of Talon2000.

Today when I turned on I got this...

https://youtu.be/qYigZPTkaZ8

I have done some googling and looked at similar issues on YouTube but I'm going to need some help fault finding this issue. It seems the problem lies in my analogue output as everything that is effected is none 3d based.

As can be seen in the vid.. the mountains, moon, score, lives, radar and sites are all screwed up.

I'd be very grateful if anyone can point me in the right direction. If needs be I'll even buy a used oscilloscope of eBay to get this sorted.....

Just an added note....a Braze high score kit was installed last month so this can cut out any game rom issues? Plus there are no beeps on test screen.

Cheers for any info...

Kev
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Battlezone is a pet love of mine as everyone reckons its "the hardest game in the world to keep going". Ours runs days solid at shows so if I can help you get yours going again I will.

Looking at your video your board has no communication or bit-slice errors so you're not seeing an L, H or T.

My guess in this cause would be either the LF13201's, the DAC's or the TL082's in the analogue circuit under certain conditions possibly around the /CENTER signal.

OR the section of the board that drives the DVXn and DVYn lines.

The other thing it "could" be is the +/-15vDC power supply has some spiking going on - however, that entire analogue circuit is used in both test and game mode so my money is on how the chips are being driven.

I'm not familiar with the "REV OID" word I saw in test mode - have you got a ROM saver daughter card plugged in?

Doubtful but could be something screwy in the vector state machine misinterpreting some of the drawing commands.

Mitchell Gannt and me love a good Battlezone conundrum.
 

kevwolf69

Newbie
Credits
52CR
RGP said:
Battlezone is a pet love of mine as everyone reckons its "the hardest game in the world to keep going".  Ours runs days solid at shows so if I can help you get yours going again I will.

Looking at your video your board has no communication or bit-slice errors so you're not seeing an L, H or T.

My guess in this cause would be either the LF13201's, the DAC's or the TL082's in the analogue circuit under certain conditions possibly around the /CENTER signal.

OR the section of the board that drives the DVXn and DVYn lines.

The other thing it "could" be is the +/-15vDC power supply has some spiking going on - however, that entire analogue circuit is used in both test and game mode so my money is on how the chips are being driven.

I'm not familiar with the "REV OID" word I saw in test mode - have you got a ROM saver daughter card plugged in?

Doubtful but could be something screwy in the vector state machine misinterpreting some of the drawing commands.

Mitchell Gannt and me love a good Battlezone conundrum.

I have a braze kit installed so that might be the Rev confusion right there. I've got a thread giong in klov to just to cover all my bases. I'm no expert so any ideas will have to be specific in their description. Thanks for the reply though. Hopefully in the next couple of weeks I'll see this sorted.
 

kevwolf69

Newbie
Credits
52CR
OK just got back from my holidays and spent some time replacing and socketing the 74LS194 data shifters at A6, D6, A5, B5, C5 and D5 after advice from a guyv that had similar issues. Guess what....it's worse! I'm pretty sure it's not my dodgy soldering so I'm assuming it's dud replacement chips. I got them off evilbay and the guy that sold me them actually sent me spares just in case there were a few duds. I should have known. Oh well.

When i power on now there is no display no test screen and I get beeps. 2low 1high 1low.

So to be honest I think it's time to send out to an expert. Anyone out there feel up to a challenge??
 

kevwolf69

Newbie
Credits
52CR
RGP said:
Battlezone is a pet love of mine as everyone reckons its "the hardest game in the world to keep going".  Ours runs days solid at shows so if I can help you get yours going again I will.

Looking at your video your board has no communication or bit-slice errors so you're not seeing an L, H or T.

My guess in this cause would be either the LF13201's, the DAC's or the TL082's in the analogue circuit under certain conditions possibly around the /CENTER signal.

OR the section of the board that drives the DVXn and DVYn lines.

The other thing it "could" be is the +/-15vDC power supply has some spiking going on - however, that entire analogue circuit is used in both test and game mode so my money is on how the chips are being driven.

I'm not familiar with the "REV OID" word I saw in test mode - have you got a ROM saver daughter card plugged in?

Doubtful but could be something screwy in the vector state machine misinterpreting some of the drawing commands.

Mitchell Gannt and me love a good Battlezone conundrum.

You mentioned you take your's to shows? I don't suppose you were at this year's NERG event up here in Gateshead? If you were then i played on your machine!

I don't suppose you take on repair jobs? As You can see from my update things aren't going well with this board! Sighs....
 
Top