3d printers

porchy

Active member
Feedback
5 (100%)
Credits
994CR
I've had on for a while now and its had its uses but haven't used it in ages.
I made quite a few cases for various electronics projects and they have been great.
 

porchy

Active member
Feedback
5 (100%)
Credits
994CR
Honestly I don't know. I'm not that creative really but there were quite a lot of plugins for it at one point.
It's free to download, or at least it was when it was Google's. I think it was sold off to Trimble or something like that.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
I just came across this year old thread, and thought it might we worth a quick revisit.

I've had a 3D printer for a while now and to be honest there are not many arcade
parts that I'd trust it to print. The finish and strength simply aren't good enough
for the human interface (at least with my low-end printer).

I did however think it would be great for printing invisible things like board
spacers (I always seem to be missing these on boards).

What other thoughts of things to print have people had? (max 21x21x18cm)

I'm aware of the OutRun wheel gear on thingiverse.
 

Milky

Moderator
Staff member
vacBacker
Feedback
16 (100%)
Credits
1,037CR
Battlezone said:
I just came across this year old thread, and thought it might we worth a quick revisit.

I've had a 3D printer for a while now and to be honest there are not many arcade
parts that I'd trust it to print. The finish and strength simply aren't good enough
for the human interface (at least with my low-end printer).

I did however think it would be great for printing invisible things like board
spacers (I always seem to be missing these on boards).

What other thoughts of things to print have people had? (max 21x21x18cm)

I'm aware of the OutRun wheel gear on thingiverse.

Completely not related to arcade parts, but i could do with trying to fashion a replacement clip release switch for my boy's nerf gun.

IMG_0461_zps207666b8.jpg
Milky2016-03-09 18:04:53
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Well the spacers printed pretty well. The foot may need
a bit more work (this version needs a blob of super glue

to hold the nut in place). I'll take them along to Steve's

tomorrow if anyone wants a look.

IMG_2010.JPG
 

RustyRoses

Newbie
Credits
10CR
Battlezone, I'd love to see some of the parts that you'd consider not to be printable, but might have the desire to print them - there is a lot that can be done through re-engineering

Design for 3D printing is an art in itself ;) You can't just take a design for injection moulded ABS and knock it out in PLA layer by layer, expecting it to retain it's material properties.
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Well it's not that they aren't printable, just that I would try and find a genuine part before firing up my printer.

I don't have Outrun but the Outrun gear on Thingiverse looks like it will take a beating and need to be strong.

My entry level printer would still leave a stripey finish on literally any visible plastic piece on the outside of an arcade machine. Say a button, or button surround, Atari volcano button surround, a battlezone handle, a joystick knob etc etc. I could print all these things but even with my 0.3mm nozzle the finish will be different to the original (even after an acetone dip).

I don't think I'm really missing any plastic bits at present to set a nice challenge, but I know who to come to for help when I am.
smiley1.gif
Probably the closest I have to a "need" would be my Warlords knobs. I have two originals and two poor substitutes. In this case even a printed replacement might be better than my swap. This is the original (boy does it need a clean).

IMG_2121.JPG


Battlezone2016-05-28 09:39:25
 

Battlezone

Active member
Feedback
1 (100%)
Credits
410CR
Ok so I decided a 3D printed Warlords spinner would be better than the shiny replacement I'd been using for two of my controls. Here they all are, I'm sure you'll be able to tell which is which.

IMG_2153.JPG


Here's the totally uncommented .scad incase anyone needs it.

scad_warlords.PNG


$fn=36;

difference() {

union() {

cylinder(r=48.2/2.0, h=1.4);

translate([0,0,1.4])

cylinder(r1=48.2/2.0, r2=31.66/2.0, h=3.9-1.4);

difference() {

cylinder(r=31.66/2.0,h=18.91);

translate([0,0,18.91-1.5])

cylinder(r=27.45/2.0,h=1.5+0.1);

for(i=[1:40]) {

rotate([0,0,360/40*i])

translate([31.66/2.0-0.7,0,3.9])

cube([0.7,0.7,18.91-3.9+0.1]);

}

}

}

translate([0,0,-0.1])

cylinder(r=6.9/2.0+0.14,h=16.0+0.1);

translate([0,0,10])

rotate([0,90,0])

cylinder(r=4.0/2.0,h=31.66/2.0);

translate([0,0,10])

rotate([0,90,90])

cylinder(r=4.0/2.0,h=31.66/2.0);

}
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Looks a good job
That all looks too technical for me but your missing a knob on a machine it is better than nothing.
I'm sure with the skills and a good quality printer many things can be re manufactured for arcade machine. No idea what but when I find the need I will post.
 
Top