5v-28v USB step up PCB.

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
Hi, yeah your thoughts on this please
rps20220908_085402.jpg
my missus bought some 12v 4.2watt fans for her crafting set up not realising that USB is 5v lol. So we saw these at 65p each so thought give them a try(cheaper than returning). After hacking the USB off of a redundant lead and wiring it up it's working great (note that with these trimmer pots you need to turn the screw anticlockwise a minimum of 15 times before they become active, stuck with only 5v output if you don't). We're using it from a USB built into the socket at the moment but would this be safe to use in a PC USB.
Sorry it's not arcade related as such but I though it could come in handy somewhere within the hobby.
 

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
Not sure what it's capable of, it was described as 2 amp, We're just using a 4.2watt fan and nothing is getting hot. I believe it also will drop the voltage down to 2v so the P = V X I might be a way to tell. It has no heatsinks so I'd think it is a low wattage device, maybe I'll keep adding 2.2w bulbs to see when it fails lol
 

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
I've got a tl866 minipro+ programmer(18v)and I have in the past used a second PSU running 24v to program the 25v eproms but never had 21v available to do those ones. I'll see if it's got enough in it to allow me to have a 21v and a 25v capability for these eproms
smiley2.gif
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Like you could try feeding from a 12v rail on pc
Then to something like a Pandora’s box
Or 60 -1 pcb. See how that handles

Thing is if you have a pcb worth anywhere above £25
You probably would spend £25 on a switch mode power supply

I think some pc power supplies have volt regulator but it’s inside the cage set at factory
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
So 2 of these just for adjusting the 12v & 5v
Is this the mission?

For jamma arcade/ pinball
Amps something like this
5V/16A 12V/4ARetroman8392022-09-08 12:01:53
 

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
No mission really but you do put 5v in and not 12v. It might be able to run a small 12v audio amp. I just thought it would be handy if you only had 5v available at a point,65p is probably cheaper than 2 metres of 16/0.2 cable running back to a PSU haha. Seriously though the minipro+ extra voltages for £1.30 would be very nice indeed.
 

John Bennett

Senior Member
vacBacker
Feedback
10 (100%)
Credits
5,325CR
I reckon this is the chip inside it:

https://www.olimex.com/Products/Breadboarding/BB-PWR-3608/resources/MT3608.pdf

I wouldn't trust the 2A, they'll have pinched that off the top of the datasheet, whereas the entire circuit has to be up to the job.

It's a typical boost converter IC, which you combine with a diode, and inductor and some capacitors. The main IC will cool itself via the ground pin and the ground plane on the PCB.

Some of the similar PCBs have 4 Watt ratings, so that's 0.33A at 12V and a piffling 0.16A at 24V.

But I do think they'll have some uses if you need a low-power, obscure-voltage supply. Datasheet shows the regulation looks good at 5V, but I'd want to verify it for something delicate at a higher voltage.
 

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
Hi John, the chips got B628 on it. Do you think this device would be ok to drive the vpp pin of the 21v & 25v eproms. The 24v plug type PSU I used to burn the 25v ones only had a max rating of 1A. I was assuming that as the earlier minipros used to do 21v and were USB driven then the current needed was quite small.
 

John Bennett

Senior Member
vacBacker
Feedback
10 (100%)
Credits
5,325CR
Retroman - I think you'd quickly find an arcade PCB that killed it. My R-type boot pulls 7 Amps, and there's some big spikes at power-up for some boards. I'd just make sure you have a good SMPS.

Bones - maybe it's not that exact chip then, I was going off this advert:
MT3608 Adjustable DC-DC Step Up Converter Boost Voltage USB Mini / Type C UK | eBay

I have minimal knowledge of what you need for 21V and 25V eprom programming I'm afraid, in terms of the current needed and the precision required, I'd have to read-up. Would be somewhat surprising if they needed watts of power to do it though!
 

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
Thanks for replying John,had to get the digital microscope out to read the chip number lol. I would imagine their characteristics are quite similar in regards to their power capabilities so cheers for the link
smiley1.gif
.
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Cheers john
Yep I thought as much,

I have 3 different pi to jamma all
12 & 5v direct from harness

With varying problems arising from the power supply’s

1 arpicade. Not enough voltage from the 12v results in no controlls
The others displays the lightning symbols as not enough volts supplied

I’m wondering I think my cabs need power supply overhauls ( shotgun the caps)

Like I keep picking up 12v & 5v adaptors from sky router and the like with the idea
Of powering a jamma harness from them even though they are not adjustable..
I know why I want to do this - just to see if it works with a Pandora box..
Retroman8392022-09-08 13:53:19
 
Top