Asteroids pcb problems

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Some advice need please.
I have 3 pcbs with faults.

Pcb1 - plays fine but now and then everything disappears in the centre of the screen for about a 3 inch square.
It happened in 3 out if 15 games over about 30 mins period of playing.
Pcb2 - was repaired 12 months ago and was tested when I got it back as ok. Then out away same day into storage now doesn't boot!!! On power up both start button stay lit. Can't get the game into test mode and just makes a loud hum. Can't credit or anything.
Pcb3 - seems dead apart from the led on the board.

Pcb4 - plays perfectly but neither of the player 1 and 2 buttons light.

I have no pcb repair skils but is there anything I can try to sort any if the problems out?

Thanks for the help.

Steve
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Nothing springs to mind, and any suggestions would require some level of repair equipment and soldering skills.

Asteroids is a tricky PCB to repair, not to be confused with other PCBs due to its Digital/Analogue circuits.

As for the LEDs, not sure without looking at schemes, never seen that problem before.
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
PCB 2 looks like its worth a quick prod, seeing as how it was working fine, and now won't even boot.

Just do the obvious - reseat any socketed chips, give the board a slight flex. It'll only take you 10 minutes and got to be worth a try.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
PCB 1 - Could potentially be a monitor adjustment. Do the objects disappear from the middle of the screen at the end of the level when there's very little going on? If so, I have the same "problem" and I don't think it's a problem because my monitor was NOS and it still did it, but I think it's an adjustment of brightness / contrast maybe? Not 100% sure.

PCB 2 - Check you haven't knocked and broken the Crystal when storing the PCB. The small aluminium can looking thing near the reset button on the PCB. They stand proud of the board, are easy to damage and will cause those symptoms.

PCB 3 - Could be the same. You won't be able to do much with that one yourself.

PCB 4 - This ought to be easy enough to sort out but what tools have you got? Do you have a logic probe? If not, forget it and again, it will need to be looked at. If you have a logic probe then I'll look up the bits you need to check. Because this board goes into test mode OK, and you can therefore put it in and out of test mode, it will be possible to test it with just a volt meter.

Let us know what test kit you have. I'm also guessing you don't have a test rig which will make working on anything a nightmare.

[EDIT] Typos! My typing is crap today! I am ill though
smiley6.gif


guddler2014-01-23 14:28:19
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Thanks for the reply's. I have a logic probe which i have just bought, multimeter and thats about it,. i will try reseating the chips on the board again to see if it changes. I will also look at the crystals o make sure they are stilll there.

Cheers,

Steve
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
OK, given you have a logic probe I'll try and dig out what you need to check for the LEDs. I'm actually off sick at the minute (nothing serious) so will see what I can do later but I won't be venturing up into the cold of the shed unfortunately.
 

VectorGlow

Active member
vacBacker
Feedback
34 (100%)
Credits
900CR
Steve - I vaguely recall repairing an Asteroids for you in late 2012, presumably one of the ones that you listed is that one? PCB2 perhaps? Boards going into storage and then not working after being taken out of storage are far more common than you might think, particularly with such old boards. Chips ease out of sockets and/or old components finally die the next time that the board is powered on. Could also be a broken crystal as suggested by Guddler.

As for the faults - I think people here have made all of the easy suggestions (check monitor re PCB1 issue, board voltages, carefully re-seat any socketed chips (namely the ROMs and any socketed RAMs - do this one by one)). Oh yes, re PCB1 - presumably PCB4 doesn't exhibit the same video issue? In which case it must be a board fault with PCB1, possibly in the final vector output section or just before that (I'd be looking at the part of the circuit for the X and Y position counters, but to be honest Asteroids boards can exhibit some strange faults that are very hard to track down so it might even be a problem with the State Machine circuit, or even the Vector Timer).

Have you also tried putting all of the boards into self test? Any beeps, display issues, etc?

As for PCB4 - the Start 1/2 LEDs are driven by a 74LS174 logic chip at location N11, this has possibly failed. Do also check pins 6 and 8 on the edge connector though, ie that they are making good contact.
VectorGlow2014-01-23 20:10:32
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Hi, I have spent the day removing chips and cleaning the legs with a fibreglass pen.
Managed to get 3 boards working and unbelievably the start buttons all flash now.

I think the fourth board is defiantly in need if repair. I have tried swoppin working Anne roms and socketed chips with no luck.

Thanks for the help with this.

Steve
 
Top