Atari Battle zone

leslie

Active member
Feedback
3 (100%)
Credits
42CR
Help hi guys i am in need of assistance, re battlezone to cut a long story short i have a dead monitor in my bz ive had all the boards checked and repaired by arcader so im 100% they are working but i still have no picture on my monitor, ive taken it out and placed it in my asteroids u/r and i works fine so in guessing that it must be the power brick (the big blue capacitor) your thoughts would be most welcome
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Won't be the big blue - plays no part in powering the monitor.

Do you have neck glow?
Is the spot killer lit (red LED on the monitor deflection board)?
Do you hear any 'chatter' from the monitor?

Do you have a multi meter?
 

leslie

Active member
Feedback
3 (100%)
Credits
42CR
Morning lilley just some short answers to you few questions posed , there is no neck glow on the neck ,re the spot killer red led on monitor board comes on for a second or so and then goes out, fuses on monitor board are all fine(as it works in the asteroids) there is no chatter(but i think the game still has audio ), also the start light flashes as normal .
As you can guess im not very experienced with electrics but i do have a multi meter ,as for the big blue my thoughts were that the monitor takes its power from the brick not the power board ,so can i assume thats wrong? Thanks for all your help this is an education for me
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Yes, the monitor takes its power from the brick - but the big bile is just one component that sits on the brick and the voltages associated with the big blue have nothing to do with the monitor.

Anyway - yes, you need to start with the brick:

1) check fuse F6 on the power brick.
2) look at the picture below (what I have lifted from DLF forum):

47f8ee9cbf5ccc0969b54898ae2da6a9_zpse772bb95.jpg


That's a pic of the 15 pin connector that outputs all the power brick voltages. Unplug the connector that'll be sat in there. Power up the cab. Set your multi meter to AC. Test pins:

8&9 for 6.1V (this provides for neck glow)
13&10 for 60V (this provides power to run the monitor).
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
If the spot killer is lighting up then there's power getting to the monitor.

Check for dodgy connectors in the wiring loom. Particularly on that 6.1v
 

leslie

Active member
Feedback
3 (100%)
Credits
42CR
Lilley thanks very much for taking the time to send me a simplistic diagram of the pin lay and their voltages but mine differ greatly re 123 = 6.2 volts 4=21 volts 5&6=6 volts 7=7.2 volts 8=3.2volts 9=8.6 volts 10=15 volts 11=8.3 volts 12=32.8volts 13=29.9 volts 14=6.2 and 15=16.9 not sure if im measuring them badly but they are not even close to the diagrams voltages (my meter is set on ac )
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Sorry, but that info isn't right. I just looked at the schematics and to measure the voltage for the monitor you need to:
  • put one lead on 13, the other on 15 with meter set on AC
  • put one lead on 10, the other on 12 with meter set on AC
  • put one lead on 8, the other on 9 with meter set on AC (as already said)
Do this with the monitor disconnected first, and then repeat with it connected (by pushing your meter leads in the connector at the wire end - if that made sense).
 

leslie

Active member
Feedback
3 (100%)
Credits
42CR
Yes it does make sense. well heres the results 13&15=57 volts 10&12=57 volts and 8&9=2.9 volts when i reconnected the plug and tested the pins from the rear the readings were the same except 8&9 witch jumped up to 16.5 volts .
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
OK, so as suspected the main power to the monitor is fine (the two 60vac measurements - although only one will be used) but there's definitely something funky going on with the CRT heater voltage.

There isn't a huge amount more I can think of doing remotely, however i definitely agree that it's worth doing the same measurement on the Asteroids to compare.

I'm assuming, since you've already tried this in your Asteroids that either the BZ monitor is a G05-801 or your Asteroids isn't since 801's aren't compatible with 802/3 or WG 19V2000's...
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Awesome 2 games btw -BZ and Asteroids

Just adding in to echo what guddler has said, if your monitor is working on the asteroids cab and you're getting 16v where there should be 6.1 then something inbetween brick and monitor may not be right.

I'm not sure if I can help remotely either other than saying that I would look at switching the bricks over as that's fairly simple as its all plug in connectors - just don't unplug the voltage selector cable as its easy to put it in wrong if you don't watch which way it was - its the short cable with 2 plugs kibd of wrapped round each other going nowhere else.

If your BZ is fully working after then its something on the brick.

Purely thinking out loud, If not the brick then is it the AR2 not putting enough out for the AVG section on the game pcb as you say the spot killer led comes on then goes out - this is normal initialisation so maybe not the pcb.

An interesting problem, i'll be watching progress and help where I can.
 
Top