Atari / Namco custom chips, help please

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
Hi

Can anyone point me in the direction of an Atari / Namco manual which has the custom chips in of 37 and 38

There used in Sky kid and Dragon buster boards, but there are no manuals about for either of these! So my hope now is to find another manual with these in! I am getting some floaty pins on both chips and ram rom which I am sure is the background generation side.

It would be so much easier if there was some kind of data in some manual somewhere!! I have looked at pacland but that does not have these customs on it so mo help there sadly

can anyone help please??

thanks in advance

Andrew

IMG_1357a.jpg


This from Pacmania is the sort of thing I am after, this is the custom 27 chip which helped a lot to determine the board I have this chip is OK

cust.jpg


andrew962013-09-23 14:59:00
 

cmonkey

Active member
vacBacker
Feedback
4 (100%)
Credits
1,659CR
I'd be surprised if CUS37 and CUS38 weren't exactly the same chip as CUS36 on a Pac-Land board. Probably the tilemap generators. Sky Kid / Dragon Buster hardware is based on Pac-Land hardware but with support for vertical scrolling as well as horizontal scrolling. I think you'd probably need an extra tilemap generator to generate pre-scrolled vertical tile maps, hence why Sky Kid / Dragon Buster has two versus one in Pac-Land.

The schematics for Pac-Land are readily available so why don't you see if CUS37/38 connect to similar devices on the Sky Kid board as CUS36 does to on the Pac-Land board. The tilemap generator(s) will have a direct connection to the tile eprom(s). Pac-Land has two tile eproms, one for foreground tiles and one for background tiles. Sky Kid only has a single tile eprom as it doesn't support twin tilemaps. The tile eprom for Sky Kid is SK1-5 at position 7E. If CUS37/38 are related to tilemap generation then both of them should have a direct connection to that eprom. One of them will scroll the tiles horizontally and the other will scroll the tiles vertically. There should also be direct connections to the two 2K*8 rams at positions 10C and 10D.

Of course if you've got a Pac-Land board you could just take a risk and swap CUS37/38 for CUS36 and see if Pac-Land still works OK.
 
  • Like
Reactions: trm

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
cheers thanks cmonkey

the address lines for the tile eprom at 7E comes from the custom 37 pins 11 A3, 12 A2, 13 A1, 14 A0, all the other address lines comes from the 74ls174 at 9D and 9E, Sadly it is the A0 to A3 address lines which are floating with nothing going on, and that's from that custom 37. It is definitely no where near the pinout for the custom 36.

This is why I am after the info as its getting to guesswork now

custom 37 and 38 don't get warm either, so am suspecting it could be one of them, but have no other namco boards or custom chips to change out and see!

many thanks for your reply

@Alpha1 yep already looked for Dragon buster as that's the same board, but again no data is about as I said in first post. just nothing on the hardware at all but thanks for your reply
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
The tile ram at 10C and 10D address lines also come from the custom 37 chip pins 43 (A0) to 51 (A7) with pin 48 being a ground pin, all these lines are lacking any sort of data!! so it is either a missing input to the custom which I stand no chance of finding not knowing what goes in and out of it and where! Or the custom is indeed faulty, it don't even get warm, either way it is looking impossible now without getting the missing chip data, so looking like a total waste of time again, just my luck!! getting right peed off now getting nowhere with every darn board because of customs!!!
smiley7.gif
might be time to give up all repairs I think

so no info anywhere at all on custom 37 chip?? are these still so secret getting on for 30 years old?

andrew962013-09-23 23:36:48
 

cmonkey

Active member
vacBacker
Feedback
4 (100%)
Credits
1,659CR
Don't give up! You're obviously very skilled in getting dead boards going again and I'm sure this one will be no different.

Virtvic has a fully working Sky Kid board and lives in the South, maybe if you sent him your CUS37/38 he could try them in his board and let you know if they're OK or not. At least that way you could potentially eliminate them from your hunt.

The generating and displaying of a static tilemap appears to working OK as the big Sky Kid logo on the intro screen looks perfect to me. It's the tilemap scrolling that appears to be non-working.

I don't know how reliable Namco customs are so it's impossible for me to say whether it's one of the supporting logic chips that's died or one or both of the customs.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
andrew96 said:
so no info anywhere at all on custom 37 chip?? are these still so secret getting on for 30 years old?

More just a case of lost into the ether! There's a huge amount of stuff that was indeed kept secret at the time for commercial reasons that has since been lost when companies have been dissolved and times have moved on, or in Namco's case, since they still exist they've still never released. For all of that stuff unless someone spends the time to reverse engineer a worker then there remains no info!
 
Top