Attract screen graphic corrupt

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
My Enduro Racer plays perfectly (all video and sounds) with the exception of a few horizontal lines through the motorcycle graphic in attract mode. They are always static and in the same place after a power cycle, the game title that is overlaid on top of the bike, sits on top, looks fine and hides the lines, I cannot see any other graphical issues but I'd like to sort it as its annoying.

Image below showing the fault. I think I'm going to verify the graphic ROM's, I know there's a ton of ROM's but looking at the MAME source using my limited code reading skills, I can't see where this is specifically located. Any other thoughts on what could cause this?

Thanks as always, Mart.

2016-01-01_15.17.04.jpg
 

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
Cheers Ben, can I ask whats the theory behind this suggestion? MAME source and the manual says these are sub program roms. I'm guessing I could use MAME debugger to work it out If I understood how to use it? I will verify them this afternoon once I've moved my cabs around.

Thanks!
smiley20.gif
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
smarty said:
Cheers Ben, can I ask whats the theory behind this suggestion?

Sure. I was looking at the picture you posted and it looked like the full attract screen with some additional horizontal green lines.

I was looking at the Mame debugger and noticed that if you killed the roms at the locations I mentioned above the were the only two roms that created green horizontal lines on the attract screen. So my thoery is that these roms have a bad connection/crusty legs/bent leg. It is just a theory so I could be wrong but it is where I would start :)
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
The motorbike graphic itself is comprised of sprites not tiles. My first guess would be a dodgy EPROM.

Unfortunately, there are a HUGE number of sprite roms as you will be well aware.

My System 16 sprite viewer does not support the older Hang-On/Enduro Racer format as things stand. But I could modify it for you, so we can determine where the graphics reside...
 

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
Chris, that’s very cool of you to mod your graphic tool, thanks!

I spent the afternoon messing with this and have an update of sorts…

I have a spare set of working boards which have a few minor faults so I went about swapping boards and cable over to try and find the source of the issue.

It turns out the fault is not ROM related, but is on the large board that’s strapped to the back of the CPU board. The manual calls it the Control Board.

Using my spare board the game now work flawlessly.

The photos below show the board in question, There has been a previous repair on two RAM’s which has used IC’s that have previously been soldered to a board (perhaps this one?) the IC sockets are a mash up of different sizes and the pins that the RAM would make contact with look tarnished and not very springy.

If either of these RAM’s are removed the game runs without any foreground sprites, including the title screen motorbike where I was having issues. This appear to have been the only repair to the board and my hunch is that it’s related to the sockets, swapping the RAM’s round produced the same fault, so I will replace the sockets when I can get some, but saying that if the socket was bad it’s likely I’d be seeing issues elsewhere in the game.

There’s plenty more RAM on the board and lots of Logic, If new sockets don’t fix the issue I will have to make a loom and get it on my dining room table as it wasn’t easy working from the cabs loom this afternoon.

Thanks for your input.

2016-01-02%2B16.08.36.jpg


?

2016-01-02%2B16.09.03.jpg


?

2016-01-02%2B16.10.10.jpg


?

2016-01-02%2B16.11.05.jpg


smarty2016-01-02 19:13:24
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
Ah good detective work. The previous repair you've shown the photo of makes me feel a bit better about my recent efforts. Hideous.

I'm going to move onto looking at my (very broken) Enduro Racer PCB at some point soon. Spoiler - it has a huge f-off crack running through one of the boards! I'm not overly confident.
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
The boards appears to be peppered with Fujitsu logic chips also so it wouldn't surprise me if one of those has developed a timing issue or something along those lines.
 

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
Good thinking on the Fujitsu logic. When I get the board loomed up I'll update this thread if there is a positive outcome. I have a bad copy of Space Harrier schematics from the interweb so should be able to work from them.
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
Good spot on the ram. Look like it's 55ns whereas the board states 45ns. Maybe one has developed a faulty cell that only affects stuff at certain points.
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Glad that you manage to solve this. I was also going to suggest that roms ending 8, and IC36 were also possibilities, which dj_yt suggested, but when messing around with these roms I could only get vertical lines displayed, and not horizontal lines like you were seeing
 
Top