Bricked Triforce

Darksoft

User
Credits
17CR
Hello everybody,

one of my triforces died during a firmware update.

I tried replacing all 3 boards one by one with the ones from another Triforce and turns out that the faulty one is the base board, that can be seen below (picture copied from another thread).

triforce_bottom.jpg


I tried also replacing the top media board with a media board from a cartridge based game and the first three versions remain the same, so I conclude that Boot version, Firm version and FPGA Version are on the base board.

When it bricked it only updated from the base board the boot room. Any idea which chip it is and how to update it? My guess it's that h8S marked as B. The picture from below is an example, is not the one before the update.
WP_20150316_007.jpg


Any help would be appreciated.
 

Darksoft

User
Credits
17CR
Bumping here. The FPGA must be the Altera chip marked as C in the first picture.

My guess is that Boot version is B? How to program it?
Looks like the program lines ID0, ID1, ID2, etc are directly connected to the CPLD in E, so maybe B must be programmed via E. Just a guess....
what about firm version? Which chip is it and how to program it?
 

retrorepair

Active member
vacBacker
Feedback
26 (93%)
Credits
378CR
I would say Andy or Craig (Ordyne).

Not too hopeful though, if it is that H8S then reprogramming that will be a bitch, especially without knowing what to reprogram it with as not sure you can read out what's already on there.

Here's a couple of resources which might help a bit:

http://git.redump.net/mame/tree/src/mame/drivers/triforce.c

CMPV-DOL btw is the video DAC

https://forums.dolphin-emu.org/Thread-all-in-one-triforce-discussion-thread?pid=238187#pid238187

retrorepair2015-03-20 13:04:17
 

Darksoft

User
Credits
17CR
Actually looking at mame driver looks to me like the only one that could hold the firm version is the E chip. Or maybe the CY7C1399 which is a small 8 or 10pin chip located below the Altera (close to the flat plastic ribbon cable).

Well, in any case, the one I want to upgrade is the Boot ROM. Any clues?
 

retrorepair

Active member
vacBacker
Feedback
26 (93%)
Credits
378CR
You mean the FPGA? Most don't have on board rom and those that do don't have much.

One way to check if the SRAMs are holding data would be to see if they are fed voltage by the battery when disconnected. I sort of doubt the firmware would be held on volatile memory though.
 

Darksoft

User
Credits
17CR
ZedEx48K said:
Ordyne generally tells you it's shagged or is a bit cryptic as he still makes money fixing these, so I doubt would be much help.

Interesting....so how easy Triforces brick? I think not many...
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Darksoft said:
ZedEx48K said:
Ordyne generally tells you it's shagged or is a bit cryptic as he still makes money fixing these, so I doubt would be much help.

Interesting....so how easy Triforces brick? I think not many...

Little bit of fact and a lot of fiction there, think ZedEx48K still has the hump on as I wouldn't tell him out to modify a new monitor chassis he bought from another seller :) I don't sell them now so I can tell you that you have to pull a resistor on the neck board and replace it with a wire link!

If it's a common problem on equipment I still fix for the trade I can't really post that up on the Internet, otherwise I wouldn't have a job! :) Mario Karts are still a big item so TriForce falls under that so normally I will just tell someone if they are barking up the wrong tree or waisting their time trying to repair. That's not being cryptic, that's trying to push someone in the right direction.

Your problem isn't going to be something that happens every day! From memory there's a cpld (altera one?) that loads up another qfp with code on the fly, drop me an email and I'll grab a base board on Monday and take a look.
Can you swap any of these? I only ask as if so I can probably give you a board with a fault on to swap the part rather than trying to program it if that helps you.
 

ZedEx48K

8-Bit
Feedback
2 (100%)
Credits
1,423CR
Ordyne said:
Darksoft said:
ZedEx48K said:
Ordyne generally tells you it's shagged or is a bit cryptic as he still makes money fixing these, so I doubt would be much help.

Interesting....so how easy Triforces brick? I think not many...

Little bit of fact and a lot of fiction there, think ZedEx48K still has the hump on as I wouldn't tell him out to modify a new monitor chassis he bought from another seller :) I don't sell them now so I can tell you that you have to pull a resistor on the neck board and replace it with a wire link!

So A) you confirm what I just said (in relation to previous Tri-force posts) and B) I never asked how to mod to cure the alt chassis issues, just which way around a couple of cables went, clearly you seem to be delving in the fiction bucket.
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
You wanted to run a 666a on a sanwa 29e31s tube and wanted to know what needed to be modified.

Sorry I haven't confirmed anything you've said, you obviously think it's bad form that I don't give out info I've worked out on faults which are still a line of repair.
 

Darksoft

User
Credits
17CR
I digged a little bit further on this. If you see the manual here:
http://www.alldatasheet.com/datasheet-pdf/pdf/249566/RENESAS/HD64F2676.html

There are several operating modes depending on the value of pins MD0, MD1 and MD2, FWE and RES (See page 825).

Looks like the On-board programming modes has at the same time two modes "boot mode" and "User program mode". Both can program the flash content BY USING a "flash programming code" that must be submitted and executed to the H8S. This means that you need to use some specific Renesas program that will do all this for you (no JTAG or similar).

I have done many things with ARM and their SWD port and you need the right programm, so I guess here is the same. The thing is as pins MD0-2 are connected to the CPLD, looks like this one must be used in order to programm the H8S.

Anyone has some experience with that?
 

Darksoft

User
Credits
17CR
Ordyne said:
Your problem isn't going to be something that happens every day! From memory there's a cpld (altera one?) that loads up another qfp with code on the fly, drop me an email and I'll grab a base board on Monday and take a look.

that would be great.

Ordyne said:
Can you swap any of these? I only
ask as if so I can probably give you a board with a fault on to swap the
part rather than trying to program it if that helps you.

That would be plan B. I really would like to do the update process myself.
 

Darksoft

User
Credits
17CR
Trying to reply myself, looks like this is the official device needed to program the flash -->
http://www.digikey.com/product-detail/es/R0E00008AKCE00/R0E00008AKCE00-ND/1653655

I'm not sure yet if that's intended to be connected directly to the H8S once it's on-board or if also requires using a CPLD in the middle. 2nd one looks little probable, so I guess that Ordyne may know a way to program it using the 6pin connector on the top right of the PCB (connector of the right of the H8S).
 

Darksoft

User
Credits
17CR
Ordyne said:
Sorry I don't but it makes sense they have provision for factory assembly!

Also one must take into account that the software to update the Triforce includes all that code that goes in the CPLD, FPGA, etc....Maybe it's programmed in factory using the plug that I mentioned and future updates are done from the SH4 *signaling* the CPLD.
 
Top