Capacitor Specs

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
Evening All,

I've been recapping some old computer kit, using ready made capkits.

I wanna move on to my CBM 1701 monitor and Vectrex now, but can't find any capkits this side of the pond, and don't want to wait 3 months for them to arrive. So I've pulled the lists off Console 5's website, and have been perusing the stock at Farnell.com. So far, they seem to have most of the bits I need, but the choice is doing my head in. I realise that certain brands are better respected than others, but now I'm wondering about other specs. The Vectrex powerboard caps, for example are rated at 105 degrees. But how many hours should they be rated for at that temp? And what about the other bits? Does it matter, or is there a specific combo to go for? Any advice appreciated. Cheers.
 

ColinD

Active member
Feedback
6 (86%)
Credits
1,367CR
Panasonic FR and FM series are good base to start with if you are looking for good quality components, also Rubycon / Nichicon of a similar spec. Not all capacitors are the same !

Ideally you want..... Low ESR, High Ripple Current, Long Life and High Temperature.

The life is rated at a high temperature, so if running at a lower temp, you will get a much longer life.

High ripple current is good for Power supplies as is low ESR.

Other things to look out for are lead spacings (some modern capacitors are smaller for the same ratings) so you want the part to fit correctly and sometimes you may have to go up in voltage for a better fit.

You could probably look up what type of capacitor is already fitted.

Depending upon who you buy your cap kits from, the quality may vary, so cheap kits may not necessarily be a good thing !

ColinD2021-05-28 11:49:46
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
Thanks Colin,

That narrows things down a fair bit.

ColinD said:
Panasonic FR and FM series are good base to start with if you are looking for good quality components, also Rubycon / Nichicon of a similar spec. Not all capacitors are the same !

Ideally you want..... Low ESR, High Ripple Current, Long Life and High Temperature.

The life is rated at a high temperature, so if running at a lower temp, you will get a much longer life.

High ripple current is good for Power supplies as is low ESR.

Other things to look out for are lead spacings (some modern capacitors are smaller for the same ratings) so you want the part to fit correctly and sometimes you may have to go up in voltage for a better fit.

You could probably look up what type of capacitor is already fitted.

Depending upon who you buy your cap kits from, the quality may vary, so cheap kits may not necessarily be a good thing !
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
big10p said:
I've bought cap kits from console5 and delivery was quick. About a week, I think.

Was that recently, though? Covid + Brexit seems to have really slowed things down this year. Then there are the insane PnP & import charges. Might still work out cheaper, though...
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,092CR
RygarR said:
big10p said:
I've bought cap kits from console5 and delivery was quick. About a week, I think.

Was that recently, though? Covid + Brexit seems to have really slowed things down this year. Then there are the insane PnP & import charges. Might still work out cheaper, though...

Good point. This was before the world went pear-shaped.
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
big10p said:
RygarR said:
big10p said:
I've bought cap kits from console5 and delivery was quick. About a week, I think.

Was that recently, though? Covid + Brexit seems to have really slowed things down this year. Then there are the insane PnP & import charges. Might still work out cheaper, though...

Good point. This was before the world went pear-shaped.

Sad times :-(
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,092CR
RygarR said:
big10p said:
RygarR said:
big10p said:
I've bought cap kits from console5 and delivery was quick. About a week, I think.

Was that recently, though? Covid + Brexit seems to have really slowed things down this year. Then there are the insane PnP & import charges. Might still work out cheaper, though...

Good point. This was before the world went pear-shaped.

Sad times :-(

Yep.
smiley5.gif
Are you on the Vectrex facebook group? Might be worth asking there if anyone in the UK has ordered from Console 5 recently, and what the shipping costs/times were like.
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
I am indeed, Mr P. And I have posted about caps and capkits. Lots of friendly replies, which sadly, brought me no closer to getting any. Lol! Reckon I might as well do a pik'n'mix at Farnell, even if it does mean ending up with a few extra caps.
 

mourix

User
Credits
307CR
For substitutes you would ideally want 105C caps from a good brand. This will make sure the set stays alive for longer. You want the first tier in this list.

You need the same capacitance, but the voltage is allowed to be higher. Only raise the voltage if you have to, though. There is no benefit to do so besides of availability or spacing.

On farnell I go to "Leaded Aluminium Electrolytic Capacitors" and check the following to help the search a bit:

- In stock, no delivery surcharges, suitable for new designs

- Operating Temperature Max 105C

- The capacitance needed

- The voltage needed

Then I sort on price ascending. At this point you'll try to stick to a single brand and type of your choice if you're ocd like me. Good luck!

mourix2021-05-31 19:58:58
 

RaveN

Active member
vacBacker
Feedback
1 (100%)
Credits
1,325CR
There's no such thing as 105oC caps, it's just the specifications.
If you look at the datasheets you can have a cap rated at 105oC @ 2000hours, and another cap listed at 85oC at 10000hours, and guess which one will last longer in a PSU? It's just what measurement the manufacturer decides to publish at the forefront.

Unless you can be arsed to study the datasheets and look at the real temp/life charts, the esr at different frequencies etc.. then do what ColinD says and trust certain brands like Panasonic FR/FM/FC, set that filter in farnell, and then all you have to worry about is getting the right leg diameter.

Bear in mind the caps listed above are FAR superior than anything that was in there before. I use FM caps in most things, just because I have them spare from audio projects and they are massively overkill for arcade stuff. Even the cheapest cap will have less ESR than the one that's being replaced and be half the size.
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
Thanks Chaps,

I started going through my list on Farnell.com at lunchtime, then ran out of lunch. There are a few gaps in their stock at the mo. I'll need to come back to it tomorrow...

Cheers.
 

RaveN

Active member
vacBacker
Feedback
1 (100%)
Credits
1,325CR
The key thing with Farnell is to always tick the first 3 checkboxes under availability, and tick "remember", and then you don't have all the out of stock/re-stock BS.
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
RaveN said:
The key thing with Farnell is to always tick the first 3 checkboxes under availability, and tick "remember", and then you don't have all the out of stock/re-stock BS.

That, sir, is a top tip.

I've now finally got my order in.

Even using the filters, it took AGES. I'll end up with a few spares, and had to grab a few caps off eBay as well. The top line price was obviously more than getting the separate capkits off Console 5, but there's no extra pnp - and won't be any customs fees or VAT surprises, and at least I should have all my caps within the next few days.
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
Afternoon Chaps,

The summer has been busier than expected, and I only got back to this project at the weekend. In getting things ready, I noticed I'd made a small mistake in ordering my caps, and managed to miss out a 16V 4.7uF Electrolytic Capacitor. I do have a spare 4.7uF at 50V, though. Would using that be a wise move, or would waiting for something a bit closer to spec be a better idea?

Cheers.
 

ColinD

Active member
Feedback
6 (86%)
Credits
1,367CR
It depends what it's doing in the circuit. Chances are that it will be fine if it fits (might be a bit fatter or taller) - The legs pitch might be different though.

You may also be able to fit a 10uf 16V, as above, it depends what its doing in the circuit.
 

RygarR

Active member
vacBacker
Feedback
3 (100%)
Credits
413CR
ColinD said:
It depends what it's doing in the circuit. Chances are that it will be fine if it fits (might be a bit fatter or taller) - The legs pitch might be different though.

You may also be able to fit a 10uf 16V, as above, it depends what its doing in the circuit.

Thanks Colin. I'm not sure what it does do to be honest. I should probably check! It's on the CPU board, as opposed to the Power circuitry, however, if that makes a difference. In terms of size, I'm pretty sure it would fit. I was suprised how much smaller modern caps are than their 1980s equivalents.
 
Top