Commodore 1084S: blank screen

sylphia

Newbie
Feedback
1 (100%)
Credits
11CR
Hi,
I've recently acquired a Commodore 1084S monitor for cheap for my supergun setup.

After building a cable for rgb video + rca audio, I managed to use it for one week, with a superb picture and not so bad audio
smiley1.gif


Unfortunately, while powered on and running a game tonight, the image suddenly first went half-sized, then rolling and now the monitor is buzzing frequently with a blank screen and very weak and slightly distorted audio.

After googling the problem, this might be related to dry solder joints, which should be fixable.

I am just a little bit concerned about the charged tube inside the monitor since I guess that, even if the monitor is switched off, the tube should still hold some charge.

Has anyone ever worked on such a monitor to fix this kind of issue ? Is there an easy way to discharge the monitor ? If not, which parts of the pcbs should I avoid touching / soldering on ?

Any help highly appreciated, as I really enjoyed using this monitor !
 

grobda

"Look at the size of that thing!"
vacBacker
Feedback
7 (100%)
Credits
1,061CR
easiest way to discharge a monitor is to solder a wire to a screwdriver, tape up most of the blade, and attach the lose end of the wire to earth.

then locate the rubber circular anode cap on the top of the crt and push the screwdriver blade underneath it until it touches the metal clip under the anode cap. monitor is then discharged.

i doubt you'd get zapped from a 14" tube anyway, but its good to be on the careful side. i've fixed a couple of faults with my old philips 8833 and not had a problem. the dry joints i got were at the geometry pots, have also repaired a dead lopt and a faulty power switch.

had the monitor since I was 15, its given 22 years of service! :)
 

sylphia

Newbie
Feedback
1 (100%)
Credits
11CR
ok, some news...

I discharged the monitor and tried to look for suspicious solders. I did not find anything really fishy.

I reflowed some of them but I still have this high-pitched sound when the monitor is powered on, and a totally black screen.

Is there anything else I should check ?

I don't think that sending the monitor to a professional repair center would be worthless, as this is probably be very costly
smiley18.gif


Thanks for your inputs on this issue.

sylphia2011-11-23 16:42:41
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
High pitched sound? Could just be the HV unit 'singing' or a problem with the sync circuit *but* I have no experience of repairing this type of monitor but they all seem to be fairly simlar. That is to say, you need to troubleshoot it logically and take safety precautions.

You need to acertain first if you have high voltage and while there are plenty of ways of guessing (eg static) the best way is a high voltage probe.
 

grobda

"Look at the size of that thing!"
vacBacker
Feedback
7 (100%)
Credits
1,061CR
my 8833 'sang' - high pitched whine that descended in tone when powered off. it was a faulty lopt.

sure ive read the 1084 is based on a 8833 somewhere
 

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
grobda is correct - the majority of CM8833s (and the -II etc) and 1084s (S, D and loads of other variants) seem to be rebadged clones of each other. There are a few chassis types but from experience you'll find the insides pretty identical. You can find schematics all over the net due to the Amiga fans.

Agreed that you need to check if you have high voltage. Good luck!

timtrm2011-11-24 15:06:39
 

sylphia

Newbie
Feedback
1 (100%)
Credits
11CR
sorry, I am not sure I understood correctly.

Even if I manually discharge the tube, there are still high voltage zones that I need to probe before investigating the issue ?

Thanks
 
Top