CRT Sharpness?

G

Guests

Guest
I've been using my CRT for some time now (Hanterex Polo 25") but i've noticed that on the edges it does seem a bit blurry? the center is very nice and sharp but the edges seem blurry, i took some pictures which will hopefully help show what i mean...

2017_01_17_14_07_45.jpg


2017_01_17_14_07_59.jpg


2017_01_17_14_08_04.jpg


There are some things on the lopt which i once turned accidently thinking i was adjusting something else. "screen" and "focus" would this adjustment cause this?

I could just be looking at a older monitor and it's fairly normal. I just don't see how my Sony Trinitron screen blows this away regarding sharpness. Perhaps that is normal though? Although i have seen screens other people have here and they look so, sooo sharp and nice I'm pretty sure mine needs some tinkering?

Any help appreciated.
 

joe34

Active member
Credits
448CR
some crt's are not so good on the edges regarding focus, but with your polo monitor you might find it improves or resolves the problem by replacing the electrolytic caps to new ones
 
G

Guests

Guest
joe34 said:
some crt's are not so good on the edges regarding focus, but with your polo monitor you might find it improves or resolves the problem by replacing the electrolytic caps to new ones

Thanks for the suggestion but the chassis was recently refurbished by Gunblade and he replaced a number of caps so I think this should be ok for now?

I guess it might be due to you messing with the screen drive and focus pots. Having contrast up a bit too high can blur things, too. I recommend you go into the RR monitor test mode and re-calibrate the monitor from scratch, using this guide:

http://wiki.arcadeotaku.com/w/How_to_Correctly_Set_Up_Monitor_Colours_and_Brightness

Nice guide! Never seen that before, i will give it a go now.
smiley32.gif


rotunda2017-01-17 14:57:30
 
G

Guests

Guest
Ok we have a definite improvement after that. The textures overall are far more sharp and the edges are better. Not 100% but certainly much better.

2017_01_17_15_06_11.jpg


2017_01_17_15_06_21.jpg


I didn't touch the "screen" or "focus" on the lopt, is it worth tinkering with that too? i 100% turned one or 2 of them before by accident. Not by much but it's been moved since Gunblade did it. Also, what do these actually do out of curiosity?

Here's a picture from when Gunblade refurbished it and tested it on his screen.

IMG_20160402_164257.jpg
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
The 'AT 1' looks like some of the colours are separated out a little (ie red). Put up a white crosshatch pattern and check the convergence at the screen edges though it they are out it is hard to adjust.
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
The focus is the upper pot adjustment on the lopt. The sharpness is usually pretty good on Videocolor tubes but it's not necessarily going to be as good as a TV as the Arcade tube will probably have 1000's and 1000's of hours more than a TV on it!

By the way, you can't adjust convergance on Videocolor tubes as it's electrostatically converged at the factory - that (normally yellow) thing round the neck is the magnet that does the job of the standard rings you get on most tubes.tb20002017-01-17 15:34:32
 
G

Guests

Guest
Very true, i did think about that, the coin counter is over 250,000 so it's had some serious use haha!

Perhaps it's just old. The picture is good either way, plenty good to enjoy the game with :D

Is it worth trying to adjust the other pots on the lopt?
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
The lower pot is the screen voltage, or its sometimes referred to as the master brightness. What I normally do to set it is to put brightness to maximum on the image adjustment board, then use the screen pot on the lopt to reduce black down to black (it'll be grey with flyback lines if it's set too high). The other way to do little adjustments to convergance is to use convergance strips behind the tube, usually in between the yoke and the tube. They can take a lot of faffing about with to get a result though!
 

obcd

Active member
Credits
3,830CR
It doesn't hurt to try to adjust the focus a little. Just make sure the system is running a while before you start adjusting it (like half an hour). You will clearly see the picture become blurry and eventually sharper at some spot. Make sure you have a picture with thin lines like the crosshatch screen test.
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
tb2000 said:
By the way, you can't adjust convergance on Videocolor tubes as it's electrostatically converged at the factory - that (normally yellow) thing round the neck is the magnet that does the job of the standard rings you get on most tubes.

Perhaps, but presumably you can still adjust the convergance at the edge of the screen with the infamous stick on strips?
 
G

Guests

Guest
Had some spare time tonight so i cracked the back off the monitor and played with the "screen" and "focus" and my GOD have i got it nailed now!!!

As soon as i changed the focus... it looked AMAZING! super, super sharp picture now even on the edges!

2017_01_20_18_21_16.jpg


2017_01_20_18_21_49.jpg


My camera really isn't doing it any justice at all. In real life it looks mind blowing the quality and sharpness is unreal!

thanks for the help chaps!
 
Top