CVS

Sluggy

Active member
Feedback
1 (100%)
Credits
73CR
Hi All..... Has anyone got or can do, a pic of a Century CVS Button Control Matrix board?? Is this a real thing I cant find anything??
 

Macro

Active member
vacBacker
Feedback
4 (100%)
Credits
2,010CR
do you mean the PCB that converts CVS to Jamma ?

I did have one once, but that may have been a while ago

I also did a GAL to do the conversion, but never tested it out!
 

Sluggy

Active member
Feedback
1 (100%)
Credits
73CR
I think the conversion board is as elusive as the Matrix board itself.... the Matrix board takes multiplebutton inputs and some how converts them to 10 outputs from what i can gather?? This is the only trace of it I have found.....

Matrix.png


But if im making a dedicated cab im not sure if i need it as it looks like the diodes stop interference from other inputs??
 

Macro

Active member
vacBacker
Feedback
4 (100%)
Credits
2,010CR
No, never seen one of those

Are you doing single or dual controls ? - If it is single I did a GAL to convert from CVS wiring to normal Jamma - straight combination logic for a 24 pin GAL
 

Macro

Active member
vacBacker
Feedback
4 (100%)
Credits
2,010CR
well, the code for it looks like this ...

and I think the wiring to the CVS is basically C1-C4 = A-D, D1-D6 = E-J on CN3

-----

MODULE multiplexdecode

TITLE 'CVS to Jamma'

" Inputs

COIN1 PIN 1; // Jamma controls
START1 PIN 2; // Held High
UP PIN 3; // Active Low
DOWN PIN 4;
LEFT PIN 5;
RIGHT PIN 6;
FIRE PIN 7;
WARP PIN 8;
COIN2 PIN 9;
START2 PIN 10;
SERVICE PIN 11;

C1 PIN 13; // Multiplex Control
C2 PIN 14; // Active Low
C3 PIN 15;
C4 PIN 16;

" Output Pins

D1 PIN 17;
D2 PIN 18;
D3 PIN 19;
D4 PIN 20;
D5 PIN 21;
D6 PIN 22;

// Pins 11,13 and 23 not used

EQUATIONS
D1 = !(((C1==0) & (START1==0)) # ((C3==0) & (SERVICE==0)));

D2 = !(((C1==0) & (START2==0)) # ((C2==0) & (WARP==0)));

D3 = !((C1==0) & (COIN2==0));

D4 = !((C1==0) & (COIN1==0));

D5 = !(((C4==0) & (UP==0)) # ((C2==0) & (RIGHT==0)));

D6 = !(((C1==0) & (FIRE==0)) # ((C2==0) & (LEFT==0)) # ((C4==0) & (DOWN==0)));
END

Macro2015-12-13 22:40:58
 

Sluggy

Active member
Feedback
1 (100%)
Credits
73CR
Cool so the Gal is basically taking the Jamma Button input and if the gal gets a signal its closing the circuit for say fire button so sorry for being thick but do you still need the Diodes to stop the back feed to the other controls as they share bits at the board end?

Untitled.png


Sluggy2015-12-13 23:01:12
 

andrewsm

Active member
Feedback
1 (100%)
Credits
485CR
Hey. Just seen this post. I have a full CVS system board and sound speech board plus 6 games. Currently dead but gonna take a look once my Moonbase is going soon. Anybody got a schematic?
 

Macro

Active member
vacBacker
Feedback
4 (100%)
Credits
2,010CR
No, the GAL should handle all of that

as mentioned, I've not tested it so it may need some tweaking (although the main problem would be if the logic is high not low, but I think it is correct!)

you connected Cx and Dx to the CVS board, and 1 to 11 to the jamma edge connector - it will probably need a pull up resistor on these, say a 1k to 5v on each line.

plus of course connect GND and VSS for the GAL so it is powered.

however, it should not need any diodes.
 

favouredson

Super Star
vacBacker
Credits
1,260CR
You could make a convertor board yourself if you were feeling adventurous.
You just need three 74LS367s, a bunch of resistors a bucketful of patience and a wiring diagram...
 

Sluggy

Active member
Feedback
1 (100%)
Credits
73CR
favouredson said:
You could make a convertor board yourself if you were feeling adventurous.
You just need three 74LS367s, a bunch of resistors a bucketful of patience and a wiring diagram...

LOL you know me Garry.... when have I ever just plugged a Jamma board in and played it... I seem to get drawn to the fun stuff!!
smiley2.gif


Still.... Im still thinking why do I need any of this stuff if Im doing it as a dedicated cab surly then I just go with the pic above and stuff some diodes in line with the buttons??
 

Sluggy

Active member
Feedback
1 (100%)
Credits
73CR
I think you will be very hard pushed to find a schematic on these whats up with the board... I think you just need to start with the normal fault finding and see what you see, dead board check power- check clock- check CPU- check roms are running ect... Or if you mean how the hell do i wire this bad boy up, i can show you pinouts??
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
I have 3 or 4 Century CVS systems somewhere. I have no interest in them I can pull them out if anyone is interested to buy them.
 

Sluggy

Active member
Feedback
1 (100%)
Credits
73CR
Alpha1 said:
I have 3 or 4 Century CVS systems somewhere. I have no interest in them I can pull them out if anyone is interested to buy them.

I would certainly be interested even more so if you have converters?
 

andrewsm

Active member
Feedback
1 (100%)
Credits
485CR
I can work out the wiring so just debug which I can prob do just easier with schemqtics. The boards are dead. The clock is OK but thats about it. I've shelved it for the moment as working on Moonbase. I would be interested in a another set to buy. Probably wont get it as cheap as I bought mine for (£3!).
 
Top