Defender (Lost Power)

spencer

Newbie
Credits
1CR
Hi All

I was hoping someone could possibly help me diagnose a power fault with my original Williams Defender arcade machine.

I bought the machine a few months back and all was working well, then a few weeks ago it died. Basically when I turn on the power at the plug/mains nothing happens. Looking inside the unit I can see that the PCBs do not show any LED lights.

I used a multi-meter to trace the power coming from the mains - and I can see it reaches a large block (see image below):

IMAG2508.jpg


My guess is that the above block is a step-down transformer, and perhaps converts the power from AC to DC? Anyway, there is 240v power going into that device and no voltage coming out.

So I have a few questions that I would really appreciate if anyone can help with:

1) do you think my diagnosis as above is correct?
2) what is the device (the big solid block) called :) ?
3) should I order a replacement, or is there a more modern equivalent I should look to purchase?
4) where can I purchase such items from - I guess Ebay?
5) I live in the Bath area, are there any recommended repair engineers/people who can help nearby?

Sorry for all the questions... again would be very grateful for any help provided.

Thanks

Spencer
 

philmurr

Active member
vacBacker
Feedback
48 (100%)
Credits
2,374CR
What settings are you using on your meter to measure the voltages out of the transformer?

And which pins are you measuring across?

I'm assuming you're measuring at the large "block" at the top of the photo and not the filter at the bottom of the photo? Filters are renowned for going pop but it has to be a pretty impressive failure for a Williams transformer to fail completely.
 

chadsarcade

Lord of Vectors (tm)
Feedback
11 (100%)
Credits
443CR
I would be surprised if the transformer has failed.

Check the fuse in line with the live wire, and check you have 240v AC coming out of the filter.

Also check the connectors from the transformer are secure, as one has jumper wires to configure for 120v or 240v AC.

The transformer should have the outputs marked on the cardboard by the terminals, check with a meter set to AC and see if any pairs are outputting in the region of what they are marked.

Schematics and wiring diagrams are online if you need a reference.
 

spencer

Newbie
Credits
1CR
Hi philmurr

Please see my reply below:

> What settings are you using on your meter to measure the voltages out of the transformer?

As
I understand the transform inputs receive 240V AC - hence my multimeter
has been set to V~500. Have been successfully able to trace the power -
but interestingly it appears that power is not even reaching the
transformer (potentially) - explained below.

> And which pins are you measuring across?

Last night I ran a few tests:

Picture3.png


Picture1.png


*
I also tested the power across the back door switch - everything is
working fine. Also I ensured the switch was in the closed circuit state
when I conducted the above tests.

> I'm assuming you're measuring at the large "block" at the top of the photo and not the filter at the bottom of the photo?

Correct.

Im
now confused as to why the transformer inputs as per the above image is
not receiving any power. I disconnected and reconnected a few cables to
ensure the connections were good but that made no difference. I did
however see one device in the circuit (before reaching the transformer)
and I have no idea what this does:

Picture4.png


I dont know what this does, but maybe it is defective?

Do you have any ideas on what I should do to diagnose the problem further?

Thanks in advance.
 

spencer

Newbie
Credits
1CR
Hi chadsarcade

Regarding the fuse I tested that - just to be sure this is what I tested:

Picture2.png


> Also check the connectors from the transformer are secure, as one has jumper wires to configure for 120v or 240v AC.

Just to be sure, when you say connectors I assume you are asking whether the wires are soldered to them? The connectors all seem to be soldered quite well, none seem to have fallen away.

> The transformer should have the outputs marked on the cardboard by the
terminals, check with a meter set to AC and see if any pairs are
outputting in the region of what they are marked.

This is one of my issues, the cardboard seems to be ancient and all faded - the text is not legible :( If you can provide any indication as to what the connectors expect as an input/output that would be great.

Cheers
 

spencer

Newbie
Credits
1CR
Hi Chad,

I just read your reply and was in tears laughing - also I was thinking no way could this be the problem because I did not even know there was a switch there! Anyway, I just checked the switch and as suggested I moved it into the other position ... and....

Yep, that was it - LOL!

Well I have no idea how that switch was moved into the other position - one of my friends perhaps, I feel rather silly but also quite happy because it appears there is no fault - yay!

Awesome, thanks for your help :)
 

chadsarcade

Lord of Vectors (tm)
Feedback
11 (100%)
Credits
443CR
Excellent, nice to have an easy fix! Yes, it's well hidden away. I recall playing BITD and a mate tying his shoelaces spotted it with a "what's this thing?" and he turned the cab off mid game :(

Still, you know more about the Defender power distribution than before so it's all worthwhile!
 
Top