Duff Naomi?

Voodoo

Newbie
Credits
5CR
Hi all,

Just picked up a Naomi 1 motherboard, which appears to be faulty. I'm running it through my test rig (supergun, atx psu, Capcom io) - the fans on the board spin up, red and green led's come on, but I get no video (monitor does clunk and look like its adjusting, but no picture) or audio. I've checked the voltages at the output on the IO board, and they are all spot on. I've tried hooking up a separate PSU, no difference. I've checked the supercap, and it doesn't appear to have leaked.

Any ideas on what I should check next?
 

Retro Muel

Newbie
Credits
13CR
Are you using a 15khz monitor? You're probably outputting at 480p (31khz). You'll have to flip a dip switch on the filter board to enable 480i.
 

pobtastic

Moderator
Staff member
vacBacker
Feedback
2 (100%)
Credits
477CR
It can take 20 seconds plus for a Naomi to do anything, are you waiting long enough? Second, they're particularly power hungry - check out your voltage.

Pobster
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
I found in the past that a known working Naomi 1 motherboard would not run off an ATX power supply that I had here. The same power supply would run a Naomi 2 quite happily. So unless you're running a proper Naomi PSU then I wouldn't still rule out the power supply.
 

bbz149

Active member
vacBacker
Feedback
26 (100%)
Credits
1,608CR
Had one with the same problem and it was forked!

Am I correct to say it's only the Naomi 2 that wont boot if the little Fans on the Board is not spinning correctly as there are speed Sensor on the Fans?
bbz1492015-10-21 16:18:18
 

Voodoo

Newbie
Credits
5CR
I have tried three different power supplies, just to be on the safe side. That's what I'm coming to think. Seller says he tested it before he sent it, but I think the postal service has disagreed with it. Voodoo2015-10-21 16:18:44
 

TonyElyod

Active member
Credits
266CR
bbz149 said:
Had one with the same problem and it was forked!

Am I correct to say it's only the Naomi 2 that wont boot if the little Fans on the Board is not spinning correctly as there are speed Sensor on the Fans?

You are indeed Correct...!!
smiley4.gif


GAME ON...............................
smiley20.gif
 

Shun

Active member
Feedback
1 (100%)
Credits
498CR
I remember having a similar issue when connecting a Capcom IO up to a Naomi 1.
I was running mine with a net dimm and the one power supply was not enough to power the Naomi, Net Dimm and Capcom IO.

I hooked up two separate PSUs to my setup, one for the Capcom IO and one for the Naomi/NetDimm and it worked.

I would try this even if you are not running a NetDimm in the Naomi.
 

bbz149

Active member
vacBacker
Feedback
26 (100%)
Credits
1,608CR
TonyElyod said:
bbz149 said:
Had one with the same problem and it was forked!

Am I correct to say it's only the Naomi 2 that wont boot if the little Fans on the Board is not spinning correctly as there are speed Sensor on the Fans?

You are indeed Correct...!!
smiley4.gif


GAME ON...............................
smiley20.gif
smiley20.gif
 

Voodoo

Newbie
Credits
5CR
I've tried it both ways - with just the power from the jamma edge, and again with a separate PSU direct to the Naomi. Am I correct in thinking I should still get a boot screen without a cart?
 

Shun

Active member
Feedback
1 (100%)
Credits
498CR
It could be an issue with the monitor not being able to display the Naomi correctly.
I hooked up a Naomi board via VGA to an HD TV and it wouldn't display anything, however it worked
with a flat screen monitor.
You should get a boot screen without a cart plugged in.

My first glimmer of hope was when I hooked up the sound to the Naomi and got the boot "jingle"
Even though nothing was showing on the TV.

If you have another monitor, I would try hooking it up to that with no game plugged in
and the Naomi powered directly from a PSU. Also make sure that the sound is hooked up.
 

Voodoo

Newbie
Credits
5CR
It's sounding more and more like its FUBAR. Tried 3 different LCD monitors and a CRT monitor - had the sound wired to an amped speaker, but no sound and no picture. I guess I'll work my way through a pile of spare psu's just to make sure.
 

Shun

Active member
Feedback
1 (100%)
Credits
498CR
Hmm, that doesn't sound good. I know it's been mentioned above about the fans
causing an issue on the Naomi 2 boards but I swear that I've read somewhere that
if the CPU fan isn't spinning on a Naomi 1 that it won't boot. It might be worth checking.
 

Brettster

Arcade, and the Chuck Norris effect
vacBacker
Feedback
23 (100%)
Credits
1,276CR
Has the supercap leaked?
its the small round cap thes mounted on wide metal tabs, you can see it without a cart in.
you can see a sticky or shiny residue on the board, and it eats away at the traces on the motherboard. can be fixed if that is the problem
could also try swapping the bios chip if you have another naomi 1 handy
 

Voodoo

Newbie
Credits
5CR
The supercap looks fine, and there is no residue on the board. I have burnt another bios, and I still get the same result.
 

Shun

Active member
Feedback
1 (100%)
Credits
498CR
I can't think of any other test that you could carry out. I would let the seller know that
you've tried all sorts of different configurations to get it working and it doesn't appear to be booting and that you would like a refund/replacement.
 
Top