Fly back and other issues

The seeker

Active member
Feedback
1 (100%)
Credits
71CR
Hi folks looking for some help figuring out the chassis on this monitor ? The fly back is arcing at the anode and the whole board is covered in an 80’s arcade gloop but I do need to buy a new fly back for sure any pointer or tips can you guys see any other issues , monitor is slow to focus but after afew minutes is crystal clear normal but last night the arcing caused a burning smell leading me to investigate
98D44BC8-31B1-4D80-B7FB-50AEE04A9601.jpeg
2C696375-1BD5-4FEB-8913-947E94A7B2E5.jpeg
 

gunblade

Active member
vacBacker
Feedback
23 (100%)
Credits
9,132CR
you need to clean the area around the anode cap with a light cleaning solution and make sure its bone dry, on the chassis itself you should use an air compressor to blow off the dust

if you are going to go down the full cleaning route you will need to remove every transformer, mains smoothing cap and coil and flyback and then replace every electrolytic cap
 

The seeker

Active member
Feedback
1 (100%)
Credits
71CR
Hi do you think I can reuse the anode if I take off clean around the are and reuse the cap applying the gel sealer stuff I used last time I can’t rember the product name / do you think I can re use this cap
 

gunblade

Active member
vacBacker
Feedback
23 (100%)
Credits
9,132CR
so what you do is discarge the anode and take the anode out of the tube, websearch discharging a crt

you don't actually remove the cap from the wire, you just disconnect the ht wire from the tube by means of unclipping it

dielectric grease is sometimes used to seal the anode cap after cleaning but i don't use it

cleaner max strength something like glass cleaner as you do not want to damage the anti corona dope around the anode of the tube

use a hairdryer to dry the tube and yoke, but not too hot or too close

wise to blast the entire monitor using an air compressor
 

The seeker

Active member
Feedback
1 (100%)
Credits
71CR
ok as a update for others, i discharged the CRT took off the anode cleaned and reattached using silicon sealer around the edge - this was perfect no more arcing. another issue i am have is a very slow start up time say black for 10 seconds then very slowly the image comes on the whole process to go from switch on to getting the "true colours" take about 5-10 minutes tho once the image is up and running its great - but i do worry about the start up time it used to only take 20 seconds ... any thoughts? many thanks for the help guys
 

The seeker

Active member
Feedback
1 (100%)
Credits
71CR
Stil struggling to get a quick start up on the arcade , the picture is fine once it become clear but it takes at least 5 minutes if not longer to warm
Up should I try to warp up the solder joints ? If so where do I start ? If it’s a cap kit can anyone advise on someone to fix it or caps needed ? Thanks for now
 

The seeker

Active member
Feedback
1 (100%)
Credits
71CR
How do you know these things , I have looked all over to find the model number and you can just tell a mile off ! Amazing :) will order cap kit and report back
 

gunblade

Active member
vacBacker
Feedback
23 (100%)
Credits
9,132CR
pretty rare chassis tbh

if you go ahead on the caps yourself then only do so if you have good soldering skills otherwise you will end up with a dead rare chassis
 

The seeker

Active member
Feedback
1 (100%)
Credits
71CR
rock and a hard place tho really, im stuck as the issue seems it will only get worse, would it be worth just reheating the solder on the caps before going all out replacing ? if i took the boards off the monitor is there anyone in the uk that can do the work? i wont like the monitor image is brilliant when it works it just takes an age to start up or should i just let sleeping dogs lie ?
 

bones

Active member
Feedback
15 (100%)
Credits
1,628CR
It definitely would be worth biting the bullet with this one and sending it away to one of the experts on here to do a cap kit replacement. They're old (the caps that is lol ) and should replaced anyway for piece of mind. Also if the issue isn't just cap related they will resolve that for you too, I like to think of it more like an overdue service like some people do with cars rather than waiting for them to conk out. The fun bit is removing the anode which I've got to do on a Polo later, I'll end up with an insulated electrical screwdriver with a wire stripped back and wrapped around the blade connected to earth hoping it doesn't bite me lol.
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,579CR
Yeah that's a G19, I don't even know if there's new flybacks available for those like there is for the G07. Last time I sorted one for someone I had to use a used one from a parts chassis I had.
 
Top