Gorf RAM board problem

shrunkenmaster

Active member
vacBacker
Feedback
2 (100%)
Credits
162CR
I have a friend's Gorf cocktail here to troubleshoot (well, Gorf boards in a Universal cocktail). I just had a look at the boards and there's a blown component on the first RAM board, also a trace is broken.

Questions:

1) What's the black component (C2) that is shot?

2) What could cause this damage?

3) Can it be fixed? I don't trust my soldering skills here...

DSC01085.jpg


DSC01086.jpg
 

Ronnie Dent

Active member
vacBacker
Feedback
15 (100%)
Credits
1,206CR
C usually denotes Capacitor, maybe that one has gone short and burned the track? looks like they are polarized so maybe get away with an electrolytic if you can see the value? but sure someone else will know better

Ronnie
 

LAZORIAN

Active member
vacBacker
Feedback
2 (100%)
Credits
260CR
A similar thing happened to one of my ram boards, when a couple of them went up in smoke at the ArcAid event
smiley18.gif


I haven't got round to looking at it yet but the manual should be online, if not I can dig mine out and tell you what the replacement is.
ianski2014-09-12 20:09:01
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
Slightly off tangent here, but I have a few single GORF card PCBs in the garage. Would you be interested? I'll pull them out later today.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Burnt tracks on gorf boards seem common if one of those caps goes.

I had one on the pattern board go.

You can just about get an electrolytic in there formed to lie flat but you need a 16-25v to get in that card rack.

The manuals are online, i've consulted them several times. Very well documented too.

They are at http://arcarc.xmission.com in the Bally section

Someone needs to crack that U15 and U20 chip on the cpu card into an FPGA replacement or this is a game we'll eventually only be ever able to play in MAME.

Which reminds me I have a GORF board to get going myself.
 

cmjones01

Newbie
Credits
194CR
RGP said:
Someone needs to crack that U15 and U20 chip on the cpu card into an FPGA replacement or this is a game we'll eventually only be ever able to play in MAME.

OK, I'll bite - I do lots of programmable logic in my day job, and I'm seriously interested in making replacements for unobtainable chips. I've done one already - a floppy drive controller - which was very satisfying, and I'm fiddling around with a replacement for the 6532 RIOT on Q*Bert at the moment (yes, I know other people have done it, but with a faulty 6532 in front of me the temptation was too much!).

If anyone has a Gorf boardset, dead or alive, I could buy, I'd be well up for the reverse engineering challenge.

Chris
 

bbz149

Active member
vacBacker
Feedback
26 (100%)
Credits
1,608CR
Alpha1 said:
Slightly off tangent here, but I have a few single GORF card PCBs in the garage. Would you be interested? I'll pull them out later today.
You still got them
smiley36.gif
Tried getting these off you like 2 Years ago along with the 2 Super Hangon boards
smiley5.gif
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
bbz149 said:
Alpha1 said:
Slightly off tangent here, but I have a few single GORF card PCBs in the garage. Would you be interested? I'll pull them out later today.
You still got them 
smiley36.gif
 Tried getting these off you like 2 Years ago along with the 2 Super Hangon boards 
smiley5.gif

And naturally i'm always looking for any spare parts for GORF.
 

Hurray Banana

Moderator
Staff member
vacBacker
Feedback
8 (100%)
Credits
2,755CR
RGP said:
bbz149 said:
Alpha1 said:
Slightly off tangent here, but I have a few single GORF card PCBs in the garage. Would you be interested? I'll pull them out later today.
You still got them
smiley36.gif
Tried getting these off you like 2 Years ago along with the 2 Super Hangon boards
smiley5.gif

And naturally i'm always looking for any spare parts for GORF.

ditto
smiley1.gif
 
Top