HP 10529 Logic Comparitor HELP!

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
I should be able to have a nose this evening unless someone has the info sooner. Doesn't look like it's immediately obvious in the schematic though...
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Thanks guys

I had assumed that all the diodes are the same value, but it would seem not judging from the image that Paul posted.

Do you think I can repair this? Or am I looking at the long drawn out process of sourcing another?
 

PaulSwan

ZZZ
Feedback
1 (100%)
Credits
1,118CR
Check with the schematics but they probably are all the same or almost all the same. Should be repairable - just need a pile of those diodes and a new DIP switch bank. Should be easy :)
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
They're all the same HP part number. But that's the problem. The schematics don't tell you what they are - they just give you the HP part number. Might be worth a question on the TechTools list if it can't be read off the diodes themselves (which I assume it can't).
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Thanks Paul

I do like easy, looking at the manual/schemes, it only appears to list one type of diode so you are probably right dude;

untitled.GIF


Are these just general purpose 'switching' diodes? I should be able to get these from Maplins right?
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
guddler said:
They're all the same HP part number. But that's the problem. The schematics don't tell you what they are - they just give you the HP part number. Might be worth a question on the TechTools list if it can't be read off the diodes themselves (which I assume it can't).

Thanks Martin

The diodes on my ZIF board have no markings, but the one that Paul posted does, unfortunately I don't know very much about diodes apart from what they do.

What is TechTools??
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
A mailing list about technical repair equipment. Not specifically aimed at arcade folk by any means but there's certainly a lot of arcade folk on it. Google 'techtools flippers' - it's run by John of Johns Jukes and his site is something like flippers.com?

There's an archive of it somewhere which google should turn up too.

I'll have a look at mine in a bit see if I can read anything...
 

Adrian Purser

Moderator
Staff member
vacBacker
Feedback
2 (100%)
Credits
213CR
They look like germanium diodes providing over/under voltage protection. If that's the case then the card should still work without them but you run the risk of damaging the comparator if something goes wrong. My comparator came with a bunch of smaller cards that you can solder chips into and these are very basic and don't have any of these diodes. Anyway, not much of a help finding the diodes I'm affraid. I'm no expert on them. I did a quick search and found that a 1N100A is a germanium diode but I'm having trouble reading the number from the picture. All I can make out is '100'
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
adrian purser said:
They look like germanium diodes providing over/under voltage protection. If that's the case then the card should still work without them but you run the risk of damaging the comparator if something goes wrong. My comparator came with a bunch of smaller cards that you can solder chips into and these are very basic and don't have any of these diodes. Anyway, not much of a help finding the diodes I'm affraid. I'm no expert on them. I did a quick search and found that a 1N100A is a germanium diode but I'm having trouble reading the number from the picture. All I can make out is '100'

Thanks dude

Yes they are indeed germanium diodes, I did wonder why they were not on the permanent reference cards. I did think if you soldered in a DIL socket, and some switches on one of those you would pretty much have another equivalant of a ZIF board really.

I can see some germanium diodes on ebay, not really sure which ones to get? However guessing I would say these;

http://cgi.ebay.co.uk/2-x-OA91-Germanium-Diodes-Germanium-Signal-Diodes-/130459850734?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item1e600357ee
 
Top