mysticmonk
Active member
Hi all,
finally got a flash card and matching boot rom for my killer instinct 2 board. But i'm getting nowhere fast, in fact I'm going backwards!
Heres the background.
1) Originally, years ago, I was getting the repeating blue boot screen. That's fine, it was 99% sure to be the hard drive.
2) Just recently I booted it up again. Not getting the blue screen anymore, but instead a garbled screen of short horizontal lines. Just went straight to that screen and nothing more. Tried it with and without the original hard-drive, same result. No audio either.
3) Thought I'd get the flash card kit (and boot rom). It arrived, plugged it all in......same result, just a garbled screen.
here is the screen I got.....http://www.thekillerinstinctproject.com/kiproject/images/backwards.jpg
(I took that link from "the killer instinct project" website, and he references that image as the result of plugging the boot rom in backwards.....but mine definitely wasn't! it was the correct orientation)
4) So the flashkit didn't change anything (wasn't fully expecting it to, but figured it would be good to have eventually anyway)
As it was all powered up, I pushed with a tiny bit of pressure on one of the chips, and hey presto, I got a solid light grey screen. It wasn't a particular chip, as I found that just pushing a bit on that area of the board (near the heat sink) had the same effect, just a solid grey screen.)
5) So by now I'm thinking this is some sort of progress, that theres something funky with the board, loose connection maybe. I then disconnect and eyeball the board a bit more. It was clean to begin with, but I gently cleaned off a few more specks of grime hidden between narrow gaps.
6) Turn it back on, and now I'm getting absolutely zilch! Double checked the board visually, cant see anything wrong with traces or connections.....but obviously something I cleaned has done something serious (I cant stress enough how little I did to the board!). Really inspected the heat-sink legs too, very sure it isn't the problem.
Neither of the 2 red leds comes on anymore (just the slightest dull flicker on the HD led when initially powered). Tried pushing on the board again....nothing.
So at this point I'm like http://reactiongifs.com/?p=15995
I think this board is toast, but if anyone has a clue it would be greatly appreciated. I just haven't come across the "grey screen" referenced anywhere, or anything like this.
finally got a flash card and matching boot rom for my killer instinct 2 board. But i'm getting nowhere fast, in fact I'm going backwards!
Heres the background.
1) Originally, years ago, I was getting the repeating blue boot screen. That's fine, it was 99% sure to be the hard drive.
2) Just recently I booted it up again. Not getting the blue screen anymore, but instead a garbled screen of short horizontal lines. Just went straight to that screen and nothing more. Tried it with and without the original hard-drive, same result. No audio either.
3) Thought I'd get the flash card kit (and boot rom). It arrived, plugged it all in......same result, just a garbled screen.
here is the screen I got.....http://www.thekillerinstinctproject.com/kiproject/images/backwards.jpg
(I took that link from "the killer instinct project" website, and he references that image as the result of plugging the boot rom in backwards.....but mine definitely wasn't! it was the correct orientation)
4) So the flashkit didn't change anything (wasn't fully expecting it to, but figured it would be good to have eventually anyway)
As it was all powered up, I pushed with a tiny bit of pressure on one of the chips, and hey presto, I got a solid light grey screen. It wasn't a particular chip, as I found that just pushing a bit on that area of the board (near the heat sink) had the same effect, just a solid grey screen.)
5) So by now I'm thinking this is some sort of progress, that theres something funky with the board, loose connection maybe. I then disconnect and eyeball the board a bit more. It was clean to begin with, but I gently cleaned off a few more specks of grime hidden between narrow gaps.
6) Turn it back on, and now I'm getting absolutely zilch! Double checked the board visually, cant see anything wrong with traces or connections.....but obviously something I cleaned has done something serious (I cant stress enough how little I did to the board!). Really inspected the heat-sink legs too, very sure it isn't the problem.
Neither of the 2 red leds comes on anymore (just the slightest dull flicker on the HD led when initially powered). Tried pushing on the board again....nothing.
So at this point I'm like http://reactiongifs.com/?p=15995
I think this board is toast, but if anyone has a clue it would be greatly appreciated. I just haven't come across the "grey screen" referenced anywhere, or anything like this.