lindbergh force feedback question

[Vamino]

Did you ever solve your Problem?

I just tried to put some new lindbergh drive boards in my ferrari Twin to Play outrun 2.

I got 2 different errors:




-drive board not connected

-drive board: (1) original point error

The steering Wheel is not turning during bootup, is this normal on Lindbergh cabs?

It was turning when i had installed the chihiro like on model 3 bootup.

Can someone show some pictures of how the boards are connected or a bootup Video.

On Ringedge the steering wheel turns at the initialisation message.
I would guess Linbergh does the same thing.

Let me know what pictures you need and I'll take some from my home made ID8 setup.
I'm using a Model 3 wheel from a Sega Rally 2 and it works OK.

 

[Vamino]

 

[Soundmaster]

Thank you for your help, i think i have everything connected right..

My wheel is not initialising at the startup. I got two cabs, on one cab the Drive Board has ä flashing light, the other board nothing happens...

 

[Vamino]

Thank you for your help, i think i have everything connected right..

My wheel is not initialising at the startup. I got two cabs, on one cab the Drive Board has ä flashing light, the other board nothing happens...

I can't help with how you have your cab wired, but both boards should flash before they initialise.
I've just taken a short movie from power up of the Ringedge to loaded into the game.

At 27 seconds Ringedge Posts and one of the LED's on the I/O board goes solid.
At 1:32 the FFB Initialises and then the flashing LED on the drive board goes solid.

What I/O board are you using?
Have you swapped/changed any of the wiring around?
If I remember correctly you have to change something when swapping from Midi drive board to Serial drive board.

 

[Vamino]

Pic of my wiring if that helps?

One mistake I did when wiring the loom was to joining RX to RX instead of TX to RX and RX to TX.
Also, what brand of RS485/422 convertor are you using? Apparently some convertors can cause issues.

Vamino2018-02-06 23:27:57

 

[Outrun2]

Could this be I/O board related? I know a type 3 is used in Lindbergh/Ringedge, but Soundmaster is using a type 2 I believe (F355 cab).

I've never had anything post Chihiro so I'm just guessing on this.. might be worth trying though.

 

[Soundmaster]

Thanks again for the help. The Videos are Vera usefull. Because the lack of time i wasnt able to take pictures, but My board has almost the same flashing red led. But its flashing all the time Also after ä few minutes. My converter board is defenitely ä different on 232 to 422 only. Will take pictures tomorow.

I have the jvs board typ 2 and i think thats why the shifters are Not working. I dont think That is causing the drive board error.
I think i have to swap it anyway....

 

[Sbdesign]

I stumbled on this thread when I was wondering something...

What sega drive boards / hardware is needed to run a lindbergh.

Have a Model 2 racer: Sega Rally

and a Model 3 racer: Sega Rally 2 / Daytona 2




What would be required to power a lindbergh for initial D/Outrun / R-tuned (i think its called)?

Anyone know?




Would a new dash/motor/encoder/driveboard/power supply/amps be needed? or is some stuff re-usable.

thanks

Sbdesign2018-10-23 19:37:07

 

[Vamino]

You can reuse the dash and some of the wiring from the drive boards to the wheel, and of course the step down. So you would need to source/make the rest of the loom, use a type 3 I/O + serial drive board and some other bits and bobs like serial convertor etc. Since you have 24khz monitors you would also need at the bare minimum a convertor/monitor that accepts 31khz or a 720p LCD.

If you had a JVS driver like Outrun/Initial D 1-3, Club Kart it would be a much easier conversion.