Logic probe weirdness

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
I've had some weird issues going on with my logic probe, and I can't understand it.

For example I would probe the ground pin on a 245 and it showed nothing. If I tried the other pins they would all be high.

Tried different power supply and that did the same.

So I got another brand new probe tried it on the first power supply and it's doing the same

Tried it on another power supply and it's the same awell

Is it possible that the 1st power supply, which is just a standard PC PSU has fried both the logic probes?

I don't get it

I've used the same setup before, with my logic probe and its been fine
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Yup, on both supplies, the voltage is just over 5v DC which is fine for the probe. Operating minimum is 4v DC

As said I've used the probe on one of the supplies before without issue

Both probes just don't function anymore
Purity2014-10-16 21:46:09
 

obcd

Active member
Credits
3,830CR
So, if you measure the voltage between your logic board gnd and your logic probe gnd, it measures zero.

If you touch the probe it's own gnd with it, does it indicate a low or nothing as well?

Could the GND be disconnected somewhere on the board? (Very unlikely I know)
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
The voltage between the pcb gnd and the logic probe gnd is 0.04v DC

If I touch the probe against its own ground I get nothing

The same occurs on different boards.

Purity2014-10-16 22:05:13
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
The original one is an RS

and the new one is a Tenma

I'm convinced they are both broken, but I just don't know how. They won't have been operated using more than +5v
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Purity said:
The original one is an RS

and the new one is a Tenma

I'm convinced they are both broken, but I just don't know how.  They won't have been operated using more than +5v

The RS one will be like mine then. Have you tried using it on an active line? Like Clock on CPU?
 

obcd

Active member
Credits
3,830CR
What's the maximum supply voltage that is recommended?

Maybe the pc supply 12V output is a better option? Usually it will be lower than 12V if the load on the 5V is small.
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
obcd said:
What's the maximum supply voltage that is recommended?

Maybe the pc supply 12V output is a better option? Usually it will be lower than 12V if the load on the 5V is small.

No +5VDC is plenty, +12VDC will probably kill it. It is a TTL Probe not CMOS.
 

obcd

Active member
Credits
3,830CR
We used to have a Tandy (Radio Shack) Logic probe. It had a switch to select TTL or Cmos logic. Inside, there were just some transistors, no TTL ic's. It's supply voltage was 5 - 15V
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Dumb question maybe, but this PSU you're using, is it the same PSU that is powering the PCB? It wants to be. And the grounds need to be shared between them (which I think has been covered already).

Have you mentioned what the 5v measures on the PCB? Maybe the ground potential difference has creeped up to the point that GND is no longer registering 0v. If you have one, I'd look at see what it looks like on a scope and check for what the levels read at low and high and also how much AC noise there is on it. Both those things could make it appear to do what you're describing, but it's all very unusual I must say!
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
Yes the PSU I'm using is powering the PCB and logic probe, so the grounds are shared. Usually this is how I work, but I did attach the logic probe to the PSU without having the grounds shared and I wonder if that has broken it somehow?

The PCB is measuring around 5v. I do have a scope but I'm not convinced that is working properly.

I'm not having much luck am I?
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
smiley36.gif
Shouldn't laugh, but no, you're not really !!

To be honest, connecting the logic probe to the PCB alone (as in powering both +5v and GND from it) won't break it, that's how they are normally used. You only need to make sure the grounds are commend when you doing stuff like powering from different power supplies. So if the PSU was not the one powering the PCB. * I think * I'm a bit hazy on all the ground potential lark myself but have never run into problems thankfully.

I'm a little puzzled then.
 

obcd

Active member
Credits
3,830CR
How can you attach the logic probe to the PSU without shared grounds if both pcb and logic probe are powered by the same supply? Just trying to figure out what could have damaged the probes.

2 Different supplies with no shared ground can easily have 100V AC between their GND wires.

Even a pc which is not properly grounded can have such a voltage on it's case. You can measure it holding one probe of your meter between your fingers (or connected to the earth of your power inlet) and the other to the chassis of your pc. (connected to the GND wires of the supply)
 
Top