m27c100

AndyGeezer

Active member
Feedback
1 (100%)
Credits
599CR
Hi Guys,

I need somebody to burn me up 4 x m27c100 eproms

Seems my burner doesn't support them, does modern stuff, but not old stuff.

Basically need 2 x Hot Rod BIOS chips and 2 x BBros bios chips.

Got the files, but system24 mainboard refuses to boot when I tried to use a different type of eprom - just reports IC1 and 2 as bad.
smiley7.gif


I don't have any m27c100 eproms either, smallest 32pin I got is m27c4001
 

Purity

The Oracle
vacBacker
Feedback
17 (100%)
Credits
2,999CR
My burner only does the older stuff and not the newer stuff and it says it supports that eprom:

SGS-THOMSON M27C:
M27C1000, or M28C1001(DIP)

............so I can do it for you if you can get the eproms

Cheers
Ben
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
AndyGeezer said:
does modern stuff, but not old stuff.

smiley36.gif
- that's well modern
smiley4.gif


I'd have to check my compatibility list but I'm pretty sure I'd be able to do them too but again, the ROMs would have to be supplied. Only very, very rarely do I use anything above 27512 size.
 

simonden

Active member
vacBacker
Feedback
20 (100%)
Credits
1,042CR
There were 2 versions of 27c1000's made, some were JEDEC but most were not. If you are using a compatible chip (such as a 27c010), then you need to swap legs 2 and 24 over (put the chip in a socket and use wires to swap those 2 legs).

They can also be a real pain to program (even if the prgrammer says it supports them, it normally only supports the JEDEC version) unless you have something like a McUmall with breakout headers for the legs.

EDIT: Give me a pic or the full manufacturors code of the original and I can tell you if it is a JEDEC version (in which case a 27c1001 or 27c010 will work) or not (in which case I have built an adaptor to program these, but it is 'put away' so will take a week or 2 to find).

i have both the JEDEC version and non-JEDEC-versions here if needed.
simonden2013-11-01 15:42:41
 

simonden

Active member
vacBacker
Feedback
20 (100%)
Credits
1,042CR
Andrew96 post has dissapeared?

Anyway, yes your Dataman40 can do it with no adaptor, both the Fujitsu and Sony in that list are non-JEDEC.
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
yeah sorry, i did 27c1000 when i see you need 27c100

so new pic done, as before my dataman 40 pro does these ones but i dont have any

27c100.jpg
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Yep, I've got the Dataman 48 Pro+. Very good and very flexible (I've got the psu upgrade to support old bipolar fuse roms and a 2708 module). BUT, don't have any of these ICs
smiley1.gif
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
@guddler

yep there good! I had to get a Dataman 48XP to do those bipolars and 8751 for maygay M1 fruit machine bards, it gets brought out when the 40 pro just can't cut it!
smiley36.gif
 

simonden

Active member
vacBacker
Feedback
20 (100%)
Credits
1,042CR
AndyGeezer said:
Jedec type I am sure.

Original ic type

Mitsubishi m5m27c100k

Yep - JEDEC,

Should just be able to pull a 27c010 out of a broken SF2 boot and use that.

Should also be able to program these in any programmer that supports a 27c010 (just tell the prgrammer it is a 27c010)
 

AndyGeezer

Active member
Feedback
1 (100%)
Credits
599CR
Yeah, I did try a 27c020 eproms - doubling the image.

But no joy, usually that does the trick. Was sure the pin out is the same.

Maybe its one of those daysAndyGeezer2013-11-01 18:01:34
 

simonden

Active member
vacBacker
Feedback
20 (100%)
Credits
1,042CR
Check the voltage given to the chip by the board. There are 2 versions of the m5m27c100k. One that programs at 5v and reads at 5v and another that programs at 12.5v and reads and 6v.

If you have the later, the voltage being supplied by the board will probably be out of range for the 27c020 (which will probably have a read range of 4.75-5.25v) and it will not work, you will then need to find another 6v read chip.
 

AndyGeezer

Active member
Feedback
1 (100%)
Credits
599CR
Ah found 4 suitable eproms on a mechanised attack PCB, bought the PCB untested for 99p a while back.

So fingers crossed I can get this board up an running.
 
Top