Magic Sword Completely missing text

duffcon

Newbie
Credits
1CR
Hope i'm in the right place. I found my way here from Arcadeprojects. I'll try to sum up.

have a Magic Sword board where the gameplay is missing all text
elements, no high score, no bottom information area. Just characters
and backgrounds in the main area. Sound works fine.

Also missing is the startup copyright text, title screen, & the
"winners don't use drugs" screen. The first visible screen is the sword
in the attract mode.

This was the same when the b&c boards were moved to another known good A board. So we have a b or c issue.

One suggestion was to use the arcade rom patcher found here and write unprotected roms to use a b-21 C board to test if the board was bad.

I burned the new ROMs, tossed in 2 different b-21 c-boards. both
boot to a screen that says "scroll 1 no good".

Based on MAME my
rom set is

ms30.bin = msu_30.11f mswordu Magic Sword: Heroic Fantasy (USA 900725)
ms35.bin = msu_35.11h mswordu Magic Sword: Heroic Fantasy (USA 900725)





This was identified as 'mswordu' by the rompatcher.

I'll try the patched roms with original C board (b-13 I think) and report back. If the hacked roms do allow any c board, then I could also try a B-17.

Also my new ROMs are


MX27C1000DC-15




Thanks for any help in advance.
 

duffcon

Newbie
Credits
1CR
Got some 27c010 chips in, same results. I also tried
putting back the factory C board; according to the patcher, it shouldn't
care what B chip is on the C board. With the original C board and the
patched ROMs I get a blank red screen. As a sanity check, I put back
everything and tested it with the same original issue. I then burned
some dumps of my factory 30&35 chips to another pair of 27c010 and
tried these. This produced a black screen, nothing.

So
I'm forced to believe that i'm either burning all the roms wrong or I'm
using the wrong eproms. The factory chips are mitsubishi M5M27C100K.
I've tried MX27c10000DC-15 and NM27c010q. I also compared the
datasheets and they look the same to me, though I'm not an expert.

My burning process:

select device

verify blank

open patched rom file as bin

hash=24909f9b48194e11a9fb2b9128ae5e5e


Write and verify.

I'm out of ideas.
 

TheDaddy

Senior Member
vacBacker
Feedback
14 (93%)
Credits
7,230CR
Shoot i forgot to look - Will try look later and zip files up. Check also as 1000 chips have to be programmed different as there is a couple of address lines switched.

So if the original roms are 1000 and your programmer does not program them you will need an adapter the 101 and 1000 roms are different. If i burn a 1000 i need an adapter on my TL866

bankswitch.PNG


As you can see by the image some pins are switched. I am 99% sure this is what is happening , Hence why they are not working.

Dave.

TheDaddy2021-07-03 12:06:11
 

favouredson

Super Star
vacBacker
Credits
1,260CR
TheDaddy said:
Check also as 1000 chips have to be programmed different as there is a couple of address lines switched.

Some manufacturers follow different rules.

The MX27C1000 is, according to the datasheet, JEDEC standard and can be read/programmed as a 27C010.

MX27C1000.jpg
 

TheDaddy

Senior Member
vacBacker
Feedback
14 (93%)
Credits
7,230CR
Ah yes the MX are the same pinout.

Ok so looking at the factory and your replacements they are pin compatible, I could not check earlier I only had my phone.

Not sure where to go from here, The only thing left is you are ripping the roms wrong from Aarons software.

Dave.

TheDaddy2021-07-03 13:57:41
 

duffcon

Newbie
Credits
1CR

Here's something I just noticed. So at 18,19,31,&36 I have 27c301 (hitachi). At 30 I have M5M27c100k (mitsubishi) an at 35 I have D27C1000D (NEC)

My 2 chips I have tried are as follows:
MX27C1000DC (Macronix) & NM27C010Q (National Semi).

What stands out to me is that the Output enable is on pin 2 on the original chips, but is on pin 24 on my selections. Could this be the cause?

*edit based on your info I looked at this link

https://wiki.arcadeotaku.com/w/CPS1_Repair_Logs

and it looks like my chips are non-JEDEC, and I bought JEDEC chips
sad.png


I'm learning the slow, expensive way.
 

duffcon

Newbie
Credits
1CR
I have a gq4x4, not sure what adapter it would need but I just ordered 27c301 as most of my 1mb chips are this kind. Hopefully this works ($60 of EPROMs later
smiley19.gif
)
 

GadgetFreak

Active member
vacBacker
Feedback
7 (100%)
Credits
963CR
This is my 3rd post in a different thread about this issue
smiley2.gif


The GQ4 does support HN27C301G and M27C1000 and probably others but I stopped checking!
As mentioned in other threads, make sure you are burning the '.patched' files and also its a good idea to use a D drive for the folder if you have one as some people have had issues with Windows not allowing writing to the C drive due to a protection setting.
 

duffcon

Newbie
Credits
1CR
Success, The hitachi chips worked! Basically I needed a non-jedec chip. Popped in a b-21 c-board and all is good. Finding a original b-13 board is pretty unlikely so this is a good work around! Thank you for all the help and the great tool!
 

TheDaddy

Senior Member
vacBacker
Feedback
14 (93%)
Credits
7,230CR
TheDaddy said:
Shoot i forgot to look - Will try look later and zip files up. Check also as 1000 chips have to be programmed different as there is a couple of address lines switched.

So if the original roms are 1000 and your programmer does not program them you will need an adapter the 101 and 1000 roms are different. If i burn a 1000 i need an adapter on my TL866

bankswitch.PNG


As you can see by the image some pins are switched. I am 99% sure this is what is happening , Hence why they are not working.

Dave.

Glad I was correct and you have sorted this now :)

Dave.
 
Top