Making adapter for a switcher

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
I am trying to make an adapter for a switcher for use in a Williams cab and the board it is going to need the following voltages at the 15 pin connector:

-5V

12V DCreg

-12V DCUnreg

+12V DCUnreg x2

GND x4

+5V x3

my switcher only has outputs for -5V, +5V, +12V and GND

so, although it is going to seem like an incredibly simple question to many here, how do i get the various voltages at the connector from the limited switcher ones?
 

Judder

Active member
Feedback
2 (100%)
Credits
1,009CR
This is the Williams converter from ArcadeShop.com to a switcher

http://arcadeshop.com/pics/wms-ps.jpg

I believe this will cover all of the power required to the boards but won't cover the -12V which is used by the coin door (?) so if you want all the lights and the coin mechs etc. to work you need the original power supply (or replacement) for those, and then you wire you're switcher in for powering the boards.

wms-ps.jpg
 

DanP

Administrator
Staff member
vacBacker
Feedback
5 (100%)
Credits
2,232CR
There are switchers out there that provide -12v as well but they are pretty rare. As Judder suggests have a look at the schematics to see exactly what requires the -12v and decide whether you really need it.

Dan
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
I have seen a post on KLOV which states this:

"You can use a standard supply. Connect the -12 to the -5 lug, works fine."

"Agreed. If your power supply does not have -12, then -5 will work just as well."

if that is true then i am ok i guess - i have checked the pinout from the origional PS so know where everything should go and have the 15 pin connectors to tie everything up

i am intending to keep the partially working origional ps in for the time being until i get confident enough to try and fix it so that seems to be working for the coin door etc...

chubsta2013-10-11 12:22:14
 

chadsarcade

Lord of Vectors (tm)
Feedback
11 (100%)
Credits
443CR
IIRC the -12v is used for the sound board, but it's perfectly happy with -5v.

In fact, the sound board is a throwback from the pinballs of the era - ever wondered why it has fuses, a bridge rectifier and voltage regulator on board...?
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Only leaves you missing coin door voltage (6.5AC) - you could live without that but I hate seeing a cab without coin door lighting. 2 schools of thought .... The 6.5 comes directly off the power brick / transformer so if you're leaving that in place you could just tap off that. Or just use the 5V off the switcher with . See link

The other issue with using a switcher is that you are likely to start to hit CMOS problems (high score table will corrupt, settings will be lost) which is irritating. You might want to consider sticking an NVRAM module on the board - but in all honesty it'd be easier to just rebuild the power supply you've already got in there.
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
im hoping the switcher is a temporary thing, i have just got the cab and want to tidy up the wiring a little but dont have the parts yet to rebuild the power supply, hopefully this will keep me going and then when i get the supply fixed it should be a question of just swapping the lead over
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
If you really need -12v then a negatron will do it for you. I have a Carnival JAMMA adaptor built by Mark of Retroclinic which uses one for the sound section.

Just thinking.....
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
managed to make up my first bit of wiring today and all seems to have gone well - there is no monitor fitted but the game plays blind so could be a result!
 
Top