Missile Command PCB Tech *FIXED*

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
Hi all,

I'm looking for a some opinions on a faulty MC board I have. It seems to pass self test going by the sounds and actually you can sometimes make out the 'OKs' by the RAM/ROM tests, the game will play but the whole video image is seems to be repeated multiple times across the screen and is constantly rolling horizontally.

Photos and video below:

MC1.jpg



MC2.jpg


MC3.jpg


Another area I guess the fault could be in in the Picture bit converter/Colour RAM circuits. I did socket and test the RAM at L7 and the 157 at M7 but they checked out good.

MC4.jpg


Any thoughts appreciated.
smiley20.gif


Regards, Mart.

smarty2014-10-31 17:08:05
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
Looks like a sync problem to me. Check your connections and if they are ok then you will need to trace back from vsync and hsync signals to look for problem chips.
 

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
Thanks Shep.

I went over the sync circuitry yesterday and found I had a dead output on the 74160 counter at E5 pin 12 (Output QC) was doing nothing, the signal is '128H' and it feeds into a 74153 at J3. The outputs from this chip along with two others go into the RAMS. I didn't have a 160 in my component stash so will have to wait for the postie to turn with some.

I'll report back when I've removed and tested the suspect IC.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Which RAMs does that go into, and on what input signal?

Bottom line is it looks like your game is running and the colours look fine so I'm skeptical that it is RAM related. Does it run? I know we can see that it's up and running but can you actually play it or does it crash? IIRC Missile Command is one of Atari's small wonders. Small wonder it works
smiley36.gif
But seriously, I think it uses Dynamic RAMs so the whole game running is highly dependent on correct timing signals and an upset in those timing signals very rapidly leads to a non working game. Classic Williams is a similar sort of design at a very high level in that everything is timing based.

If it were me, first thing I would do is use something that can measure the frequency (scope?) and trace back from J7 / J9 in your first schematic snippet until you find where a signal is incorrect. It doesn't look any more complex than that to me. I reckon you have a sync signal but it's not the right value.

guddler2014-10-31 11:47:09
 

shep

Active member
vacBacker
Feedback
10 (100%)
Credits
377CR
That 74160 with the duff signal also generates the 32H signal which contributes towards the HSYNC and VSYNC. If the chip is not counting correctly then it looks possible that it could be cause of this problem.
 

smarty

Ready Player One
vacBacker
Feedback
12 (100%)
Credits
1,305CR
Thanks for the input guys
smiley20.gif


I swapped out the 74160 today and the game is now fixed. The removed IC failed in my tester in a few different tests.

2014-10-31%2B16.29.16.jpg


2014-10-31%2B16.41.38.jpg


2014-10-31%2B16.41.04.jpg


Is there an easy way to test the trackball input without a trackball? I may have to wire my centipede one up to completely test it. This is the first fix on this board its never been worked on before so that's not a bad failure rate, It's got 11 ROM's and all the RAM is soldered.

Thanks again, Mart.

smarty2014-10-31 17:07:49
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Well done!

Whether it's easy or not is entirely debatable and a matter of opinion, but I once made up a tester for tron spinners using an arduino. I think. I can have a look just in case that was missile command. Either way though you should be able to make a joystick to spinner encoder with an arduino and a trackball is only two spinners, one for X and one for Y.
 
Top