Monitor brightness changes

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,085CR
I have a MAME PC fitted to my cab and noticed that the brightness gradually increases when playing games in a certain video mode. It's most noticeable on the black background which isn't illuminated at all to start (which is right), then over a few minutes becomes illuminated, like someone has turned up the monitor brightness control. When I quit back to Windows, it looks too dark.

Does this sound like a monitor component is on the way out?
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR
I have a MTC9000 with the same issue. Starts off dim and then instantly becomes super bright after a minute or two. Then randomly after 5 mins or so goes dark again. Eventually it goes bright once more :(
 

joe34

Active member
Credits
448CR
i dont claim to be an expert here (that's a bad start
smiley36.gif
) so until someone with more experience comes along, it may be:

1. dirty control pots, you can rejuvenate dirty monitor controls by spraying them with servisol super 10, then turning them left and right back and forth fully several times, but of course remember the original position the pot was set to if possible or you will have to set up the monitor controls all over again from fresh

2. check for bad solder joints at the various pins (heater pins) which look similar to these pics: http://www.dsbelec.iinet.net.au/Normal_CRT.jpg

http://s836.photobucket.com/user/mecha2001/media/Hantarex%20Polo/Hantarex%20Polo%20low%20res/IMAG0294_800x479.jpg.html

3. you may possibly have a capacitor problem and it may be necessary to use a monitor cap kit to fix the issue (or at least replace the faulty capacitor)
 

joe34

Active member
Credits
448CR
ok m8, yea see if u can find that R90 resistor (should be marked on the PCB), then give that a test with your multimeter, and see if it's ok

(did u get a multimeter, i cant remember
smiley1.gif
)
 

tb2000

Active member
Feedback
4 (100%)
Credits
3,578CR
joe34 said:
actually here's something else to check:

if your 130v B+ reading is correct, check the the resistor R90 (a 270k resistor) has not gone open circuit (ie. shagged
smiley1.gif
)

ps. dont ask me where resistor R90 is tho
smiley36.gif
... can any1 spot it? here:

http://www.kn34pc.com/sch/sch_device/mon_hantarex_mtc_9000/hantarex_mtc_9000_m3.jpg

EDIT: i think the R90 resistor is located near the flyback transformer (LOPT) maybe
R90 is a good one to check first. Quite a common fault. That's a 9000/A in that pic though! R90 is located behind the lopt as you say though, usually in line with the centre leg of the TIPL voltage regulator.
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR

gunblade

Active member
vacBacker
Feedback
23 (100%)
Credits
9,116CR
Nes4life said:
Discharged the chassis again and removed it. Found the R90 and it reads 232k which is low for a 270k resistor even with +-5%. I'll order a new one and fit it. I'll let you all know how I get on.

i changed thast resistor when i changed the lopt,232k is 270k-either you have metered it non isolated from the circuit or your meter is not very good

drop the tube and chassis to me and i said i would sort it for you
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR
Thanks Gunblade; you're right of course!
I'm not sure why I'm attempting to fix it when you've already offered to take another look
smiley29.gif
. I think i just got carried away. I'll take this to PM.
 

gunblade

Active member
vacBacker
Feedback
23 (100%)
Credits
9,116CR
Nes4life said:
Thanks Gunblade; you're right of course!
I'm not sure why I'm attempting to fix it when you've already offered to take another look
smiley29.gif
. I think i just got carried away. I'll take this to PM.

its free of charge,just drop it in-i will sort it out
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,085CR
I've had a look at the R90 resistor and read 275k across it, with it still soldered to the board. Sounds good to me, or should I really de-solder it to check it properly?

Also, is there anything else I should check while I have the chassis out?

Cheers.
 
Top