Monitor Interference From Lighting Ballast

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
Has anyone encountered monitor interference from their lighting ballast before? This manifests itself as a slight image wobble. If I disconnect the ballast and light tube, it goes completely.

I've ensured the ballast is earthed. I also spoke to cmonkey, who has the same cab (OutRun Mini), and he mentioned he had a similar issue.

dj_yt2015-08-09 22:11:19
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
Not a visible ripple. It makes the image slightly unsteady so you just see a slight wobble to anything static like text. It seems worse at the top of the monitor than the bottom. It is subtle, but noticeable enough to be annoying.
dj_yt2015-08-09 22:17:51
 

gunblade

Active member
vacBacker
Feedback
23 (100%)
Credits
9,121CR
if a ballast is too close to the tube then it will cause issues due to emf
if a ballast is wired onto the secondary of an iso this will also cause issues
 

cmonkey

Active member
vacBacker
Feedback
4 (100%)
Credits
1,659CR
Grant - is this something to do with it being a 50Hz ballast vs a 60Hz monitor and there's some interference between the two frequencies? I'm not too clued on monitor tech so this is just a guess!

If it is then it is possible to get a 60Hz ballast (maybe from a US cab?) and make it work (somehow) with 50Hz UK mains to reduce or eliminate the issue?
 

obcd

Active member
Credits
3,830CR
It's not electrical interference, it's magnetical interference. The magnetic field surrounding the ballast (which is a coil) acts upon the picture tube like a degaussing coil. In our arcade, wer start to replace all fluorescent tubes with cool white led strips. They give pretty much the same amount of light and are maintenance free. You need 12V DC to feed them, but most modern machines have some spare amps on the 12V rail. If you don't want to drive it that far, you can try to shield the ballast with a metal plate between ballast and picture tube. Another ballast, or an electronic ballast can do the trick as well. Another option is a led TL tube (they work without starter and ballast), but those are expensive and the led strips are the cheaper alternative. Just fix the led strips with a little silicone as well, as the adhesive on the back tends to become loose after a while.
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
Thanks chaps. The ballast is mounted on a small metal plate but I'm guessing it's not enough. I'll have a tinker at some point.

As I never had the original lighting setup working I've no idea whether things were always this way. The sega mini cabs are tight on space as all the components (monitor included) are pretty much the same size as the full size upright.
 

iamjimmi

Active member
vacBacker
Feedback
8 (100%)
Credits
498CR
Did you ever resolve this?

I have just posted a similar thread and thought I had solved it by changing the ballast, but as soon as I position the second balance where it should it above the monitor, the picture goes flicker - exactly the symptoms that you were getting?
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
I replaced the lighting with some modern LED under cabinet lighting. :)

Looks good, generates less heat. Didn't have to mangle the cabinet in anyway, so I could always put the original lighting back in if I wanted to.
 

iamjimmi

Active member
vacBacker
Feedback
8 (100%)
Credits
498CR
Thanks.

Very begrudgingly I think I will have to go LED...

I really like the idea of those T8 LED tubes but I can't find any in the UK that are smaller than 60cm. I'm looking for 45cm...
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
Check my jamma+ OutRun mini restoration thread. There's a link to a nice compact LED solution from CPC in there.

Can't dig out the link easily now as on a mobile! :)
 

obcd

Active member
Credits
3,830CR
We use 12V bright white led strips. You just cut them on the length you prefer. The adhesive back isn't very reliable to hold them in place, but a little transparant building silicone helps a lot.

They are cheaper than a led tl bulb. You just need to bring the 12V up and make sure your supply can handle the additional load.
 

iamjimmi

Active member
vacBacker
Feedback
8 (100%)
Credits
498CR
Thanks guys... Being lazy, I wonder if there is 120V version avail in the UK. Then I can just hook it up the power supply feeding the existing lamp supply...
iamjimmi2015-11-26 22:47:08
 

dj_yt

Active member
Feedback
3 (100%)
Credits
787CR
Here are the links to the light I used. I mounted this directly in the cabinet with the existing captive nuts:

http://cpc.farnell.com/dfx/s104/striplight-led-400mm-cold-clear/dp/LA03302?CMP=TREML007-005

or: http://cpc.farnell.com/dfx/s106/striplight-led-400mm-pure-clear/dp/LA03303

You will need to purchase a power cable.

light1.jpg


dj_yt2015-11-27 15:10:03
 

simonden

Active member
vacBacker
Feedback
20 (100%)
Credits
1,042CR
Agree with OBCD, had this in a couple of cabs, magnetic interference. Removing the ballast and using Cool White LED strips looks fantastic.

I use these instead of 12v one's though. That way you can use the existing wiring and mounts already in the cab and it doesn't matter if the cab is 110v or 240v as the input range is 110-277v. You want the 6w version for the right length.

Edit: Add link

http://www.ebay.co.uk/itm/231530845842

EDIT2: Although I don 't like those cut to length 12v strips. We have those in the Defender (was like it when we bought it) and I don't think they look right. The light looks very 'dotted' instead of one solid light. Gonna pull them out and put in some terry clips and a T8 240v LED bulb instead.
simonden2015-11-27 16:39:17
 

iamjimmi

Active member
vacBacker
Feedback
8 (100%)
Credits
498CR
simonden said:
Agree with OBCD, had this in a couple of cabs, magnetic interference.  Removing the ballast and using Cool White LED strips looks fantastic.

I use these instead of 12v one's though.  That way you can use the existing wiring and mounts already in the cab and it doesn't matter if the cab is 110v or 240v as the input range is 110-277v.  You want the 6w version for the right length.

Edit: Add link

http://www.ebay.co.uk/itm/231530845842

EDIT2:  Although I don 't like those cut to length 12v strips.  We have those in the Defender (was like it when we bought it) and I don't think they look right.  The light looks very 'dotted' instead of one solid light.  Gonna pull them out and put in some terry clips and a T8 240v LED bulb instead.

That is exactly what I am looking for... I spent hours looking for these on Ebay etc and the best I found were these:

...Ebay LED

But these were coming in at 5 times the price.

And dj_yt - thanks for your tip - and your Outrun Resto is mint
 

simonden

Active member
vacBacker
Feedback
20 (100%)
Credits
1,042CR
iamjimmi said:
That is exactly what I am looking for... I spent hours looking for these on Ebay etc and the best I found were these:

You have to search eBay.com as they don't show up on eBay.co.uk even if you select international sellers.
 
Top