Monitor Problem Help Please

Kewydee

Active member
Credits
221CR
Hey Guys.

Fired up the cab today (Spectrum Deluxe) and the colour has gone all weird.

Looks like this now

Photo0045.jpg


I have no idea how to fix this, am terrified of going anywhere near the back of the monitor.

I need the advice of the 'vac experts. Is this bad? Has a colour gun failed?

Please Help!
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,085CR
Looks like the Gain or Cut Off for green has gone low, for some reason. All RGB colour guns look to be working, though. Maybe one of the adjuster pots has failed. What monitor is it?

Give your cab a good whack on the side and see what happens.
smiley1.gif
 

Kewydee

Active member
Credits
221CR
i think its a Hanterex monitor but not 100% sure. Cab is an Electrocoin

tried a "technical tap" on side of cab. Picture wobbled, got a elec sizzle noise and then stayed the same as the picture above.

There are 3 coloured knobs red, blue, green sticking out of the side of the neck board. Is that the gain? Im bit nervous about touching anything. Am no expert and have no idea what i'm doing (as usual)
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,085CR
Yes, those knobs are the gain. Try pressing the green one in gently and giving it a couple of light taps. Also a slight twiddle back/forth - trying to leave it back in it's original position. Do this with the monitor off if you prefer.

Listen to gunblade, though. He's the expert.
 

Kewydee

Active member
Credits
221CR
Opened cab up and tried the gain knobs on the neck board with the power on.

Seems they were already cranked up to max, could only turn them down from what you see in that picture. Turned them all up / down the full range of the knob.

Green would only go down from where it was, didnt get any better.
smiley19.gif


Any other way of adjusting the green? Or does my monitor need servicing? It looks pretty dusty in there. I think the "recently serviced" spiel when i bought the cab might have been bs
smiley36.gif
(I'm no expert but that dirt looks old to me)

Cheers
 

Kewydee

Active member
Credits
221CR
Thanks for all the help guys

So, it needs a good service. Is there anyone in the Hertfordshire area that does servicing?

Or anyone that does a visiting repairman type of thing?

Am worried that a courier would just turn the tube into a jigsaw puzzle.

Whats my next move?
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,085CR
There is another adjustment for RGB Cut Off, but it sounds like it does need a service.

Ask gunblade nicely and I'm sure he'll sort you out.
smiley2.gif
You don't need send the tube, just the chassis. This will mean discharging the monitor before removing the chassis, but you should be able find a local TV guy to do that for you, if you're not keen to do it yourself.
 

Kewydee

Active member
Credits
221CR
Ah, so you dont need to send the glass tube. thats a relief.

Thanks again guys, your help is invaluable to arcade electronics noobs like me.

Good on Ya
smiley20.gif


Love the 'Vac
smiley27.gif
smiley31.gif


I will save the terror of taking the monitor apart until tomorrow
smiley5.gif
smiley23.gif
 

Kewydee

Active member
Credits
221CR
Well, what a day it has been.

After much fear, summoned up the courage to get in there and discharge the monitor.

No spark, not a peep. Did it half dozen times just to be sure it held no voltage.

Unplugged all the various wires and removed the chassis - Hooray!

Day soon went sour, the chassis is a POLO33 fitted to my 25inch tube
smiley6.gif


A few msgs with Gunblade and now I know that this isn't what it seems, the chassis must have been hacked to work on the smaller size tube and probably had the high voltage circuit tampered with. It was going to fail, just a matter of time.

This looks like a classic case of noob purchase, I didnt know what to look for at the time and consequently got sold a ringer - BUYER BEWARE

Lucky for me that the 'vac has saved me.

Gunblade has the correct chassis for my tube and have made arrangements to buy the correct one

What gets my goat is this could have been a fire hazard all along. Glad I never fell asleep with the cab on.

Thanks again for all the advice guys, your help has been tremendous

And a big
smiley20.gif
to Gunblade, he has saved my bacon, What a great guy.

Learn from my mistakes guys, know what you are buying or you might get stitched up

Cheers
 

big10p

Coins detected in pocket!
vacBacker
Feedback
13 (100%)
Credits
6,085CR
That does sound like a bit of a hack job you bought, there.
smiley18.gif
Anyway, sounds like the story will have a happy ending.
smiley20.gif


P.S. I never get a peep out of my Hanty monitors when discharging, but I always go through the motions of discharging properly, anyway.
 
Top