Monitor questions

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
I powers up some machines for new year last night and ha 3 failures.

Switched on point blanc and power supply blew. Should be an easy fix.

Switched on jamma cab and heard a very load crack from the monitor. Sounded like something blew like a cap or short. Then within a few seconds the monitor fired up with a good picture. It has a little bit of colour distortion in the top corner. It is a polo 25". Could this have been the degause circuit blown? Picture is nice just the colour distortion.

Other jamma cab- only had it a couple if weeks an never used. Switched on and had a very dim picture which started to brighten up a little after a few then minutes then just went off. Power to the board and marquee light still on.

Any ideas?

Not a great start to a new year Eve's party.

Cheers,
Steve
 

jengineer

Senior Member
vacBacker
Feedback
49 (100%)
Credits
1,205CR
The jamma cab that had the loud crack, you'll have to remove the chassis and inspect it for any burnt out caps etc?

the 2nd jamma cab, check to see if it has neck glow? if not check the fuses on the chassis or again remove for inspection

very good clear close up pictures for us aswell, if you can?

jengineer2014-01-01 12:53:24
 

IDCHAPPY

KANFU Master
vacBacker
Feedback
9 (100%)
Credits
1,523CR
I tend to stick the wee fan heaters on for an hour before firing up the cabs these days, especially if they have been off for more than a few weeks.
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
I made the fatal mistake of having them in storage for 5 months but the electrician only finished the games room at 5.30 New Year's Eve.
I will dry the rest out before switching on.

I will report back my findings later today.

Thanks,
Steve
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Tried one if the monitors again today. It is a hantrex 9110 25".
I see neck glow but no picture. When you switch off you get a flash of white on the screen. Fuses are all good. Picture was very faint a couple of days ago then faded to nothing. Would a cap kit sort it or does it sound more terminal? I have tried a could of game boards in it. They both play blind so I know it is the screen at fault.

Cheers,
Steve
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Report so far. Tried the brightness and cleaned all the pots on the monitor board with switch cleaner. Started to get a picture, then power supply failed. Replaced and after one hour I now be a nice picture.
Thanks for the input of help.

I will start another thread for the monitor problem in the point blanc 2 cab.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Your 9110 25" has only a screen brightness control which is accessible, but does have a preset brightness pot which might be out of whack.

I would be checking underneath and looking for cold/cracked solder joints at first go.

I've had a few 9110 issues where i've had neck glow, obvious static on the yoke and no picture - turned out to be no voltage going to the guns (6.3v for the heater, ~190v for the guns).
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Well just played it for 30 mins and now no screen or neck glow. All I can hear is a very quick ticking coming from them monitor.!!!

What a bummer.
 

JohnnyChaos

Blows own trumpet for CHQ cabs
Feedback
4 (100%)
Credits
325CR
ticking is HV shutdown, which means the chassis has turned off the high voltage section due to something failing. It's supposed to prevent any further damage.

sorry if you knew that
smiley1.gif

JohnnyChaos2014-01-02 19:38:35
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
I had an idea but was not too sure if that was the problem. Any idea where I start to look it should I send it off for repair?

Steve
 

JohnnyChaos

Blows own trumpet for CHQ cabs
Feedback
4 (100%)
Credits
325CR
is it a Polo?

could check this

http://gc339.free.fr/NoticesMoniteurs/Hantarex/Polo/POLO.FlowChart.jpg

I've got the same with one of mine.. it spent 3 weeks with a local TV repair guy and is now off to Gunblade!
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
It's a hantrex 9110.
I will check the net for info.

Failing that it will have to go to gun made. He has fixed some for me in the past.

Steve
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Ignore the brightness preset pot, the chassis will still run with a bad one. In fact I can guarantee every mtc9000 and 9110 will have a faulty brightness preset pot and c42 next to it unless it's been changed recently.
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Try bypassing the inductance correction board which is located at the side of the lopt, you will see the scan coil plugs into it and then the correction board plugs into the scan coil socket in the chassis. Remove the plug from the chassis and plug the scan coil directly into the chassis and see if it runs.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Ordyne said:
Ignore the brightness preset pot, the chassis will still run with a bad one. In fact I can guarantee every mtc9000 and 9110 will have a faulty brightness preset pot and c42 next to it unless it's been changed recently.

Thats industry knowledge you don't get without experience, sorry to hijack but whats the deal here? Were they all out of spec at the factory?
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
It just kills the pot and cap over time, not sure which goes first as everyone I ever saw had both of them bad
smiley36.gif
The difference a working pot and cap makes is actually very very marginal but I used to replace these all the same.
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Hi Craig, I bypassed the induction correction board and the monitor runs nice. The picture is upside down. How do I correct this?
Also can I use the monitor with the induction board bypassed?

Thanks for the help.

Steve
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
You need to replace the inductance correction board really. If you want to replace it give me an email at work to remind me as I've got some brand new ones somewhere but I'd have to dig out the how much they cost.

If you want to run it as is there should be two sockets together for the scan coil, move your connector over to the next one.
 
Top