More fun with Asteroids ram errors.

MarbleMad

Active member
Feedback
1 (100%)
Credits
106CR
Hello, Long time no talk (apart from on facebook) Like my new machine?

Well it's got me playing with my 4 dead asteroids boards again.

I managed the coax the least dead of them into test mode and it reports ram R4 as faulty (beep beep beep BUUP).
It's not though. It's had a few known good 2114 rams in there and I checked the continuity of every pin and they appear to connect up ok.

Out of self test the game generates some very odd video. You get at the top left a little dash almost like a dos prompt :)
most of the screen is blank and then along the bottom line it's got a repeating sequence of numbers '123456789012345678901234567890',etc.
if you coin up or press any inputs the character line will jump to different positions around the screen!

It's quite distinctive so I thought I'd ask if anyone's seen this one before?

Any ideas where to look next?
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
JIM!!!!!!! :D

Would you like us to merge your old list account so you have all your old mailing list emails on your account?

Ps. JIM!!!!
 

IDCHAPPY

KANFU Master
vacBacker
Feedback
9 (100%)
Credits
1,523CR
I love the term 'least dead'
smiley36.gif
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
Hey Jim. Goold old asteroids RAM errors eh? Currently battling with the last of 4 duff sets of star wars boards, one is a real pig. 7 bad ICs on one pcb alone and so far has died twice after < 2 hours of fixing despite being in safe storage and only having one fault last time I powered it up... hopefully yours task will be easier. Dare I say it might be worth asking on vectorlist if nobody pipes up here. I haven't got any immediate suggestions for your fault I'm afraid.
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
Sounds like RAM issues, but of course there may be other problems here too.

Check your buffers, they are either LS245 or D8304.
 

MarbleMad

Active member
Feedback
1 (100%)
Credits
106CR

MarbleMad

Active member
Feedback
1 (100%)
Credits
106CR
Equites said:
Sounds like RAM issues, but of course there may be other problems here too.

Check your buffers, they are either LS245 or D8304.
Could be onto something there. The board's crystal decided to crap out on me but after replacing it i was quite pleased to discover the board now runs blind. Still getting that ram error and no vectors.

Put the probe on the D8304 and a couple of the pins that connect to the ram do look a bit iffy.

Question.. since the only place i can find a D8304 is off one of my other asteroids pcbs
smiley18.gif
Can i just remove the chip at P2 and plonk a LS245 in below it at R2? Simple as that?
 

Equites

Chief Sheesher®
vacBacker
Feedback
35 (100%)
Credits
3,329CR
MarbleMad said:
Question.. since the only place i can find a D8304 is off one of my other asteroids pcbs
smiley18.gif
Can i just remove the chip at P2 and plonk a LS245 in below it at R2? Simple as that?

Yes, that should work, at least the original Atari PCB has alternative positions for either D8304 or LS245. The LS245 is more reliable than a D8304, and easier to locate!

Also, Space Wars Deluxe looks very impressive and slick! Very nice work, I would buy this.

Equites2012-10-16 09:13:37
 

MarbleMad

Active member
Feedback
1 (100%)
Credits
106CR
Progress. It appears to be passing ram test now but now the watchdog is barking. I pulled DMG0 and the game plays blind so I believe that means I have a fault in the VSM. The VSM is a mystery to me so I'll begin with PaulSwan's wise words:

"[font="arial,helv,helvetica"][size="-1"]For the VSM, check the
PROM at C8 (C9 on Asteroids) and surrounding state machine signals
for HALT, DMAGO, STOP, GO and the like. The rest is pure grunt work
to check the state machine is running properly. Someone else please
feel free to add details to the VSM debug procedure...[/size][/font]"

But any further advice would be gratefully received.
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
The nearest thing I've gained to understanding the vector generation circuitry is 'the secret life of vector generators' by Jed Margolin, it's worth a look if you haven't already done so. I did have to read it all the way through several times before it made enough sense to have any applied use but maybe that's just me.
 
Top