old topic - wobbly asteroids

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
I can't find my old topic about my Asteroids having a odd 'wobbly' graphics.

It kinda looks 'rippled' when objects fly over certain parts of the screen and the test grid lines aren't straight and have tiny bits missing in them. The lines look bowed.

I just replaced the deflection board with a mate's one and the graphics are now bang on.

Only thing is, I can't nick his board!
smiley36.gif


I did notice that my board has had the 45uF cap (C506) replaced with a modern 47uF. Also my transistors at Q705, Q704,Q703,Q604 are all bigger and don't have the heat sinks on Q705 and Q703, so they aren't screwed onto the board thru the eyelet. Could this be my problem?

Or are the screws just to hold the heatsinks in place?

This little problem has been bugging me for over a year now
smiley18.gif
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
I've just done a bit of digging and came across an article that reckons the cap on my deflection board that has been replaced is a 45 uF 125V LOW ESR capacitor.

Could the 47uF cap that replaced it be the problem?
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Couldn't say to be honest, and I'd be surprised if you're likely to find anyone else with direct experience of the issue, BUT, given where we managed to get to with this before, if you can find a low ESR cap of more or less the right value then it would certainly be worth a shot.

Without seeing the transistors, I wouldn't like to say about the heatsinks and / or screws, without the heatsinks they may be getting too hot so again, if you can find the correct / proper transistors and can then mount them properly then it would certainly be worth a try.

Just to confirm though, these are transistors on the deflection board yes? Not the chassis mounted ones?

Sounds like you're definitely narrowing it down at last.
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
I'll take a picture later (I'm off today), the transistors on the deflection board.

God knows where I'll get a low ESR cap from though? I had a quick look on RS, but nothing doing there...
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
I've just been metering the resistors - the good board meters R621 and R721 at 3.3kohm
Mine meters at 6.8kohms for both of those resistors.

Just checked the schems list - mine is correct! WTF?
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
The blue circled transistors are original. The 2 red ringed ones are the same as the blue ones on my mate's pcb. The green ones are also the same, but without the black heatsinks on my mates pcb.

All the transistors on my mate's pcb are the smaller bolted down type.

The cyan ringed resistors are the 6.8k ohms, whereas my mate's pcb has 3.3k ohms (not correct according to the parts list)

The purple ringed cap is a 47 uf (normal cap) whereas the original is a 45 uf low esr cap.

Hope this helps someone to help me!
smiley4.gif
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
ok, fifth time attempting a reply..

take a photo of your test screen, your problem sounds like its the pcb, not your monitor...
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Andy - it's not the PCB I've already had the PCB on my bench and plugged into an HP XY display it's fine. Was also fine on a 14" WG.

Obviously It would be helpful if we could find the original thread. I'll see if I can.
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
Andy - I have tried a friend's deflection board and the display is sweet, so it's got to be the deflection board.

I also have Asteroids and Asteroids deluxe in the machine with the same results.
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
Its a slim possibility its the cap, but i'd more likely say it was a silicon issue, so start to look at replacing those one by one until you find the sucker.
P-Man2012-03-19 19:39:48
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
silicon=semiconductors, ie transistors or diodes (chips on pcbs)

Its possible the Z amplifier is pulsing somehow, the lines are pretty straight i'm starting to think its not deflection related.

Try replacing Q503/Q504/Q506 in the Z amp.
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
Looking at the whole test screen, the grid is actually 'bowed'
I'll look into getting some of those transistors you mentioned and see if that helps first.

Ta!
 

P-Man

International man of mystery
Feedback
4 (100%)
Credits
1,273CR
The bowing is very minimal, and is adjusted with your linearity pots on the deflection pcb itself.. concentrate on the jaggies first. Adjustments for eliminating the bowing can be done later.
 

virtvic

The Cabaret King
Feedback
21 (96%)
Credits
2,012CR
Which sites do you guys use for finding equivalent parts codes?

I googled the TIS98 (Q503 & Q506) and found a question by none other than Phil Morris which was answered by none other than Andy Welburn
smiley36.gif
2N4401 - RS has these.

Still looking for the MPSU03 equivalent.
 
Top