outrun pcb

Gaming Heaven

Active member
Feedback
6 (100%)
Credits
106CR
forgive me if this has been asked 100 times...

my outrun has died

i tested 5v suply on the board at the connector end and was fine - not on load yet though [dont know where to test]

symptom is currently blank screen but before, shaker motor function stopped, then the sound was bit glitchy, then finally the graphics funny, scenery went missing but game played, then froze mid game and now dead

any pointers as in an idiot guide as i don't fix pcbs?!

thanks
 

forcefulfil

EDOT King
vacBacker
Feedback
17 (100%)
Credits
1,675CR
id say like you have tried,firstly check all the voltages are correct as it uses a switcher +5,12v,-5vetc etc ,checking all connections etc.
secondly try to re-seat any eproms.

other than than id say if all else fails your gonna need a repair,and outrun are NOT an easy pcb to work on,however there are guys who repair these

phil
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
I think the interconnects between the PCBs are suspect on these boards as well. I would suspect trying the usual diagnoses for a non booting board apply, eg clock signals, reset lines, ROM verify, yada yada but I don't know how the 2 cpus talk to each other. The schematics do exist in the public domain now at least but i didn't consider them very user friendly. I managed to fix one outrun that had dodgy sound once (turned out to be a bad ram) but apart from that no experience. If you don't have any test equipment and don't want to buy any there are some people I believe repair them, I think retroclinic does but don't quote me on it and drop them a line to ask first....
 

Gaming Heaven

Active member
Feedback
6 (100%)
Credits
106CR
can anyone by any chance give me an idiots guide to checking 5v on the board end?

i know the 2 cables that connect at the bottom of each board feed power in at 5v, but where - and i mean exactly, do i put my 2 probes to check the voltage?

i now have several outrun boards to test and get this cab working and work out which of the seperate boards are bad and which are good

thanks!
 

karlcdoe

Active member
vacBacker
Feedback
8 (100%)
Credits
887CR
I think you'll find people are generally quite busy so it might be a heads up if you did some research on the internet first as people will be more willing to anwser the obscure questions later on... However, where exactly you measure the voltage on the boards isn't that critical but you could pick a point(s) that is furthest from the power inputs as that is where the voltage is likely to be lowest. I usually I just pick any 74 series logic chip and measure the power across that since the power inputs on these chips are generally all the same (look up a datasheet for a 74LS244 for example). If is sometimes easier to just measure the power across one of the electrolytic caps on the board though (less opportunity to short other pins out by mistake) I believe they are mounted on the four corners of at least one of the pcbs in the layer.
karlcdoe2012-10-19 14:55:21
 

Judder

Active member
Feedback
2 (100%)
Credits
1,009CR
Gaming Heaven said:
can anyone by any chance give me an idiots guide to checking 5v on the board end?

i know the 2 cables that connect at the bottom of each board feed power in at 5v, but where - and i mean exactly, do i put my 2 probes to check the voltage?

i now have several outrun boards to test and get this cab working and work out which of the seperate boards are bad and which are good

First thing first is to find the owners manual and/or schematic to the game you are working on and locate the connector you want to test.

20 second search on Google gives me this Outrun Schematic which amusingly has the words "TOP SECRET" stamped all over it
smiley36.gif


Here's the Outrun owners manual too

If you look on page 40 of the Outrun owners manual you can see the full schematic showing each of the boards and how they connect together.

The power supply board is top LEFT, and there are two main output blocks - a 4 pin molex and a 6 pin molex shown where it says "839-0035 PWR AMP"

To test the power supply output, you need to measure between a Ground and a power output.

So if you look at the top of power supply board you can see the +5V regulated supply - you need to follow the wires from that to the other boards and measure what you are getting with a voltmeter.

I'm sure the other guys can add more but this the basics of what I do with my machines...

Judder2012-10-19 11:47:47
 
Top