Point Blank - Some Issues

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
Hi guys,

One gun works fine. The other gun doesn't do sh*t.

I need to get on and fix this... no idea where to start!

I would presume I need to replace a part in the gun?

ANY help welcome! I've not done anything like this before
smiley9.gif


(More details and issues added as thread goes on...)

maskeddev2017-03-06 09:23:25
 

Jinxz

Newbie
Credits
21CR
Based on what test are you sure that the gun doesn't work? Ingame or did you also check the cailbration?
Did you swap guns to be sure it is the gun that is broken? After you checked that and the gun also doesn't work on the other side I would swap the PCB inside the guns to see if it isn't the wiring/pcb.

Hope that helps.
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
That does help, thanks. I'll go that route and see where I end up next.

I bought the cab knowing one gun doesn't work. I've done no tests other than coining up player two and seeing that it does indeed not fire in game!
 

bonehead

I'll get pix tonight
vacBacker
Feedback
50 (100%)
Credits
1,729CR
Could be a faulty micro switch but as mentioned try plugging in the gun to player one and see if it works then. Could also be a missing lense at the end of the gun or the small pcb inside faulty.
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
Hi guys,

So I got the gun firing. Took it apart and put back together again. I've also put a new sensor in there. Although... calibration issue.

The gun can't see about the bottom third of the screen. When you start going up, cursor reaches the top of the screen and then jumps down about a third again and goes up again. I can see the pot value matching this.

I simply cannot calibrate it!

Help? Something the gun connects to at fault maybe?
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
OK, making no progress on this really... have found a wire that seems to not be connected to anything. Guess I should hook that up ro something. I'll add pictures later.

I think I must have some grounding issues in this cab. We had to put this together again after it fell apart and the wiring is a bit of a mess... Anyone have a nice example point blank machine that wouldn't mind taking some pics for us? I'm looking at schematics and I don't really get it.
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
Got the PCB stack put. Looks clean as a whistle, can't see anything obviously wrong...

I have two other issues though and half expected to find something. Those issues are 1) the gun calibration screen is almost garbage and 2) music often stops after a couple of seconds but. Sound effects are fine.

Grounding wires all over the place maybe?!

Pissed with this machine now.
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
Sorry for spamming, on a phone atm.

Have spotted a couple of bits here and there. Where can I get a PCB schematic from? The manual only covers the array.
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
So sound seems to work for now. Took PCB stack out, turned up the volume, put back in. Played through the beginner levels, sound didn't cut out once. Maybe that's that one sorted! Seems like a heat/switch issue though so doubt it's gone away.

The calibration screen being really sh*t and the second gun being "a third off" has led me to look closely at this PCB. It's Namco System NB-1 so not a lot of details on the PCB available. I did not two potential areas to look at though. I've not touched a PCB ever, and am only going by my uncommon sense... what you think of these two pics please:

http://i.imgur.com/dQ4TkAY.jpg

http://i.imgur.com/5AUbeCE.jpg

I could do with getting the chassis serviced as I have wavy geometry around the edges (and it get wavier on some menu screens). Don't think this is causing the gun issues as both guns not affected in the same way.

Any help with the PCB welcome! Looks like I may need to clean with isopropryl... and maybe find someone who can touch these two bits up, idk?
 

mathj

Active member
Feedback
5 (100%)
Credits
499CR
have you tried swapping the plugs for the guns over to see if the calibration issue follows the guns or stays on the same side, that will help narrow down whats at fault

hth

math
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
mathj said:
have you tried swapping the plugs for the guns over to see if the calibration issue follows the guns or stays on the same side, that will help narrow down whats at fault

hth

math

Will give that a go this evening as it's now a really simple test for me, thanks!

The actual calibration screen itself is so f**ked I should take some video footage.
 

maskeddev

Active member
Feedback
5 (100%)
Credits
88CR
Swapping the guns over proved to be an issue as Gun 1 doesn't reach Plug 2.
I'd need to remove the gun from the CP so need to summon a lots of will power ifI am to continue with that test.

I tried Gun 2 (the one with the issue) on Plug 1. It worked fine.

The issue is not with the gun then but with the loom/pcb somewhere? Has this test narrowed it down to that or do I need to get the other gun off the control panel and on to this other plug?
 
Top