Polo 3 line down screen

Ste72

Active member
Feedback
3 (100%)
Credits
152CR
Hi

Just set-up this monitor and it has a line down the screen that sometimes get brighter. Is this a cap-kit issue or something else / worse? Image is immaculate otherwise.

Any advice appreciated. Thanks

Polo_3_line_v1.jpg
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Have you tried adjusting the
Horizontal position & width

To see if the line moves with the image or disappears
Some times a little bit of out of sync like screen folding can cause more illumination.
I can see screen width is pulled in, extend width, and try moving width position also Retroman8392022-05-28 20:25:51
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Does it get wider
As the screen gets wider ?

I could def replicate it horizontaly in. a few of my monitors
Before image folds

There is a horizontal pot on the cassi Retroman8392022-05-28 20:50:27
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Ste72 said:
No stays same size / width
53CDFD4D-99CB-483A-9628-78D740863F19.jpeg


This is the polo 2 hori pot
Not sure if related to your issue
I have never had a polo 3..
But this is the master pot for width on polo2

Are you trying different games ?

Is this jojo’s ( not related to problem but just curious )
smiley5.gif
 

Ste72

Active member
Feedback
3 (100%)
Credits
152CR
Correct - jojos
smiley20.gif


I'll check the chassis later for that pot. I've tried the game on the old polo 1 I was swapping over (lots of burn in) and no issues.
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Ste72 said:
Correct - jojos
smiley20.gif


I'll check the chassis later for that pot. I've tried the game on the old polo 1 I was swapping over (lots of burn in) and no issues.

Seems a common issue with hantarex fly back or neck resistor copy
Paste this link in your browser
http://forum.arcadecontrols.com/index.php?topic=132071.0

Retroman8392022-05-28 22:58:03
 

Ste72

Active member
Feedback
3 (100%)
Credits
152CR
Thanks for your help. I did some more adjustments to the level I'm comfortable with but no joy. Brightness and contrast help but just hide it. The line is always in the same place and same width. Really frustrating as the monitor is absolutely perfect otherwise.

Tried with final fight pcb too.

IMG_20220529_185519_copy_756x1008.jpg
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Did you read the link,
What Gunblade says.

R36 r37 need checking ( right next to the tube socket on the kneck pcb
Some of the 240v caps…

But most of what people put I down to also is a bad flyback …
You could get a new flyback but well worth checking the two little resistors?

in this hanterex chassi occurred time to time.
Can also be a black line and also on the right side of screen
But most people mention left side..

I also read it could be small caps inside the flyback Retroman8392022-05-29 20:10:13
 

Ste72

Active member
Feedback
3 (100%)
Credits
152CR
Yes thanks for finding the link. So looks ultimately fixable. One to ask Gunblade for a chassis repair then? Or tb2000?

Much appreciated.
 

Retroman839

Senior Member
vacBacker
Feedback
13 (100%)
Credits
8,288CR
Yep exactly!
Have it looked at
Happy to help.
You got a perfect monitor tube there deserves
Chassis Gets sorted..

Sounds of it There was a bad batch of flybacks that came along for the hantarex
I read Some repair guy had to chuck a load because they were giving this excact same fault.

Retroman8392022-05-29 20:23:20
 
Top