Poorly Pleiads

OTTOTHEMADANDEVIL

Will gyrate for Gyruss
Feedback
3 (100%)
Credits
328CR
Well, it looks like I spoke too soon yesterday.

My Pleiads PCB is not 100% after all.....

I have run it in attract mode for 4 hours + and it looks and sounds great.

The issue happens during game play, after you clear the first screen you ship starts to take of then the game just starts wigging out (technical term).

Ive tried this several times now and the game crashes out at exactly the same point when you start and take off.....

Any Ideas?

I am uploading a video onto youtube but its taking a million years.....

I'll add it as soon as its finished.

Cheers guys
smiley20.gif
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
could be a bad rom that is accessed during level 2

a dump to check it would be an idea

yeah you don't have a burner so send the board here I will check it, send me phoenix too so I can free play it toosilverfox07862015-02-01 18:06:56
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
I'd be more inclined to think an IC was bad, which access the banks on the roms

the IC that triggers the next bank of data for level 2 isn't being triggered

what IC that Is I cant say without looking at schematics or knowing the boardws layout, im also pants at board repairs
 

OTTOTHEMADANDEVIL

Will gyrate for Gyruss
Feedback
3 (100%)
Credits
328CR
What the hell are these little green things and where can I buy some from?!

I have 2 on the board with broken legs so assume thats something to do with the problem...?

All it says is 0.1K & 50 written underneath .......
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
I just told you what they are above mate

I only have 0.22 ones here in stock but will get you a link for some

0.1 is 0.1 micro farad

k is tolerance +- 20%

and 50 is VOLTs 50Voltssilverfox07862015-02-01 20:25:52
 

philmurr

Active member
vacBacker
Feedback
48 (100%)
Credits
2,374CR
Very unlikely they've anything to do with the problem, just decoupling caps. Still looks to me like a ROM issue,

Anyway there's a couple of those caps on their way to you in the post.
 

silverfox0786

Beware the Hillman
Feedback
47 (100%)
Credits
2,699CR
philmurr said:
Very unlikely they've anything to do with the problem, just decoupling caps.  Still looks to me like a ROM issue,

I thought the same and do think the same but boards can be funny old things

Bubble Bobble is one prime example

2 Electronic caps that are in the middle edge of the board will kill graphics if they are faulty or broken

they also look like decoupling caps
 

cmjones01

Newbie
Credits
194CR
I think the green capacitors are a red herring. I've got a Tehkan Pleiads board here, too, and half the green decoupling capacitors have broken off with no ill effect. They're put everywhere on the board because it's a good habit, not because they're guaranteed to be necessary.

The error at the end of the first level looks like a graphics logic problem, not a ROM one, to me at least. The screen goes crazy in a way that it would hard for a ROM fault to achieve. Pleiads and Phoenix have pretty simple graphics: they're essentially two planes of characters, one of which is scrollable. There are no sprites.

The scrolling is done by two adders, IC4 and IC9 (both 74LS283). They add an offset to the row address to move one plane in one-line steps. The offset comes from a latch at IC10 (74LS374). The row address also has an effect on the data selectors IC15/19/33/37 (all 74LS151) which could be going crazy with a certain combination of inputs, though I'd expect that to be trouble all the time, not just when scrolling.

Tricky one to diagnose, since you have to be playing the game in order to get the fault! I might start by disabling the latch at IC10 (quick and dirty just grounding pin 11 would do for now) and see if the fault still happens. That should stop scrolling working.

The video RAM is all 2114, and they're always prime suspects for failing, so piggybacking them one by one might help, too, though it doesn't look very RAM-fault-like.

Actually, once the fault has occurred, does it stay like that? If so, wandering around IC4, IC9 and IC10 with a scope or logic probe to see what's in what state could be interesting, as well as scoping the divider chain IC2/7/20/38 (all 74LS163) to see if the row/column counters are still making sense.

HTH

Chris
 
Top