Powerdrift cockpit help !!

the-hat

Active member
Credits
71CR
Help,

anyone else got one of these beasts, or similar game on the same hardware ? could really do with talking to someone about it.
Mine is all working bar the movement now, it has 2 motors, 1 for side movement and 1 vibration. Neither work so i think its unlikely to be the driver boards as there is 1 for each motor. There is 300v DC present from the power supply to both boards (is this correct ? :/ im guessing so)
that pretty much leaves either the main game pcb stack (unlikely) or the small-ish pcb sat on top of the main pcb cage (think this), or of course a safety cutout is triggered. If I put my hand in front of either of the laser beams at the sides the led at one end lights so im guessing they are not faulty..

aarghhh
 

system11

Active member
Feedback
9 (100%)
Credits
345CR
It's a long shot, but was the PCB always in that machine? There are dip switches for upright/cockpit etc usually and that might simply turn off the motors. I am grabbing at straws here - Craig will probably be the authority on how it works.
 

the-hat

Active member
Credits
71CR
Yeh already checked the dips and they are set for moving. When you say spare board, you presumably mean the main set not the extra board (839-0213) that is extra for the cockpit ( this is the board i suspect is faulty)

Thanks guys
 

BristolMartin

Active member
vacBacker
Feedback
0 (50%)
Credits
382CR
I suspect it is the movement board, same as outrun and space harrier I have. I have been told they are rare as anything and you just wont get another.
 

the-hat

Active member
Credits
71CR
Thanks,

Ive taken a couple of pics here. sorry for all the linkies !

The main pcb set:
http://www.hatster.co.uk/powerdrift/IMG_2801.jpg

dip switches on main pcb:
http://www.hatster.co.uk/powerdrift/IMG_2798.jpg

A pic of the smaller pcb in place: (i suspect this to be at fault)
http://www.hatster.co.uk/powerdrift/IMG_2805.jpg

close up of this pcb (anyone got schems for this?)
http://www.hatster.co.uk/powerdrift/IMG_2808.jpg

motor controller for the sideways movement: (the right connector goes straight to the motor) (the middle connector, measuring from green to any of the other wires gives 300vDC)
http://www.hatster.co.uk/powerdrift/IMG_2811.jpg

screenshot in test mode:
http://www.hatster.co.uk/powerdrift/IMG_2799.jpg

and heres the beast !!
http://www.hatster.co.uk/powerdrift/IMG_2815.jpg

on the smaller pcb there is a largeish IDC connector, should this be connected to anything ?
Bristolmartin: Which board were you referring to which you said would be impossible to obtain a replacement ?
hatster2013-03-17 13:59:42
 

Jodo

Boy is this a machine!
Staff member
vacBacker
Feedback
15 (100%)
Credits
607CR
Mark at Retroclinic can rebuild your motor drive board (he did mine), although he's taking a break whilst moving house I believe.

Drop him a mail - it's always worth asking
smiley1.gif


http://retroclinic.com/
 

the-hat

Active member
Credits
71CR
on this pcb there is a bank of 4 dip switches. These are all set to off, is this right ? anyone know what they do ?

thanks,
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Outrun & Space harrier use totally different systems, their info isn't relevant to this set up. You won't find schems for the control and drive boards Kev, the problems are usually on the drive boards though. Do you have limit switches in the set up? If so can you check them in test, just to see if the comms from the game board to the control board is working.

Rebuilding a harrier/outrun drive board is pretty easy, there's little logic on it so you can just shotgun the board, this system is a bit more in depth, I doubt your going to be able to shotgun this one without causing more issues.
 

the-hat

Active member
Credits
71CR
thanks for the feedback d00d, i assumed the control board as both motors are not working but i guess its probable that the operator didnt repair it when the first motor stopped, then the second also... I dont know about limit switches how would i use them to test it ?
The sideways motor has an optical wheel on it, i could move the motor by hand in test mode and see if the co-ords change.

I did think about the shotgun idea on the control board, as its mostly logic. there is a z80 on a socket which i can change easily so may try that later.
 

Ordyne

Active member
vacBacker
Feedback
5 (100%)
Credits
1,282CR
Sounds like a plan turning the motor if it shows the encoders position in test. I'm trying to remember what the boards is like in afterburner dlx as I seem to remember its similar.
 

the-hat

Active member
Credits
71CR
ok quick update on this as i had 5 mins to spare this morning...

i bought a spare motor board (the one with loads of heatsinks, etc) and stuck this in, exactly the same (not known good but you never know!). If i put the machine into banking motor test mode i get a screen up with quite a bit of info. the motor obviously doesnt move, but if i manually turn it to tilt the machine then the co-ordinates of the motor change. so the opto encoder in the motor is working which in turn means that part of the control pcb is working. There is a laser each side of the machine to shut down movement if anyone breaks the beam. If i put my hand in the way and block the beam a LED lights at one end of the beam but on the screen nothing changes, it still says safety sensor = off. Also if I turn the motor as far as I can so the machine is fully tilted it still says limit sensor = off same as before. so can i assume there is a logic fault on the control pcb ?

any ideas ??????
 
Top