Robotron PSU help

R177

Newbie
Credits
11CR
Been away from the forum for a while and my Williams Robotron has sat in a corner feeling sorry for itself for too long now.
smiley18.gif


To recap, it's showing a RAM 31 error. I've tried swapping with a good RAM, no joy. Consensus of opinion was that the PSU needs a rebuild. I was going to have it done for me but I now fancy a wee bash at it myself. Lack of funds preventing me from sending it away!

Can anyone supply me with all the parts that I'll need and maybe a wee bit of 'what goes where' help? I've seen the kit I need on the 'Real Bob Roberts' website (Wms Def/Star/Bub/Rob/Jou OEM PS REPAIR Kit - $10.00) but I emailed them and got no reply. Can anyone help?
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
This lot should do it. Don't think any of these parts too difficult to find:



Part



Position





Defender



All others



Capacitors







22μf 10v



C10



C11



47μf 50v



C2



C15



100μf 25v



C3



C2



100μf 25v



C7



C16



220μf 16v



C14



C13



330μf 10v



C4



C5



1000μf 25v



C6



C3



4700μf 35v



C13



C14









Voltage Regulators







LM723



IC1



IC1



LM723



IC2



IC2









Transistors







2N3055



heat sink



heat sink







 

R177

Newbie
Credits
11CR
Thanks for your quick reply.

Will I be able to pick those components up at a Tandy? I see them on RS Components and on eBay but they're in large multipacks which I don't need.

Is there anyone, maybe on here, that'll sell me the whole set (like Bob Roberts does)?
 

trm

Who loves you, and who do you love?
Feedback
2 (100%)
Credits
2,877CR
Wow! I never knew Tandy was still around until I just googled.

Checked their site and they don't carry the bits you need. However a quick check shows Maplin do carry everything you need.

http://www.maplin.co.uk/

The 4700uF cap only seems to be 36V in the "normal" range but they've got a ridiculous "audio grade" version that's rated for 50V so I'd probably find one from eBay cos a few of them will still be cheaper than the £7 Maplin want!

For the 2N3055 transistor the Bob Roberts picture suggests you need it in TO3 style which is Maplin p/n BL45Y.

Suitable sockets for the two LM voltage regulators are BL18U (2 of)

All capacitors should be electrolytic type and with a voltage rating of at least that listed in the table from tb lilley.

Everything you need is in the last pair of posts, so 15 mins on http://www.maplin.co.uk/ and you're sorted!
 

Judder

Active member
Feedback
2 (100%)
Credits
1,009CR
I've got the Bob Roberts instructions at home somewhere from a US import that included Bob Robert's kit (he does reply to emails normally) so I'll scan those in for you as it points out where the capacitors are you need to change (*although honestly if you follow your nose it's really easy).

For getting the capacitors to swap-in, £9.99 of your hard earned cash should get you all the types of capacitor you need, bar the big 4700uF 35V one, in a single pack from our good friends at Maplin.

From a quick scan of the image I can see:

- 220uF 25V

- 47uF 25V

- 100uF 25V

- 10uF 50V

and there's 10 types and lots of each so you have spares for your next boiler / monitor / something else re-cap that you will need to do probably one day :)

http://www.maplin.co.uk/radial-electrolytic-capacitor-120-piece-pack-44037

Big Image - http://images.maplin.co.uk/full/n68bt.jpg

n68bt.jpg


I had a weird situation with my spare power supply where I re-capped it, and then one of the voltages dropped (*the +5V if I remember correctly) so I've been to re-check my work just in-case one didn't have a rock solid connection.

BTW Bob's kit is very reasonably priced for getting everything in one go :)

HTH

Judder2013-10-29 16:10:32
 

R177

Newbie
Credits
11CR
Thanks for all the help guys, I picked up everything on the list from various eBay sellers (ended up costing around £13 for the lot which I can live with) and I'll use TB Lilleys table above to point me in the right direction. I have the drawing set for my Robotron so I should be OK, fingers crossed!

Once the parts arrive I'll let you know how it all goes
smiley24.gif


This really is an invaluable forum though, don't know where I'd be without it!

Thanks again for the info.
smiley20.gif
 

forcefulfil

EDOT King
vacBacker
Feedback
17 (100%)
Credits
1,675CR
iirc the kits in the UK were over a tenner,so thats not bad value tbh
but sadly the 2 main guys who did sell them here in the UK no longer do anymore
smiley19.gif


re-solder all the header pins too,these are a common failure too

Keep us posted!!
 

R177

Newbie
Credits
11CR
OK, rebuilt my PSU with all the parts mentioned above....BUT I'm still getting RAM 31 error message on the startup tests.:(

Voltages on RAM 31 are:
pin 1: -4.96
pin 8: 11.86
pin 9: 4.84

I realise that pin 9 is too low and should be nearer 5v.
Any idea's ?

I can add credit, start a game but the screen is frozen and doesn't play. Also, the 'fancy attract mode' looks like this >>

 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Have you reflowed header pins on PSU and Robotron CPU board? If not, I'd try that next. Also worth reading the voltages from the output pins on PSU. Compare to what's finding its way to the board / RAM.
 

R177

Newbie
Credits
11CR
tb lilley said:
Have you reflowed header pins on PSU and Robotron CPU board? If not, I'd try that next. Also worth reading the voltages from the output pins on PSU. Compare to what's finding its way to the board / RAM.

That's what I did'nt do! I'm away for a week so won't get a chance to try it. When I'm back next week I'll reflow all the header pins and check in and out voltages.
Thanks again
smiley1.gif
 

R177

Newbie
Credits
11CR
OK, resoldered all the header pins, then replaced all the caps that I'd already replaced just in case! But, I'm still only getting between 4.96v and 4.98v output from the PSU. Also still getting the RAM 31 error!

Am I missing something somewhere?
smiley5.gif
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
You could remove resistor R10 from the power supply board. See if that lifts the voltage. But power may not be your problem here. I'd expect the boards to run fine with 4.9.

Might be worth a try though.
 

R177

Newbie
Credits
11CR
Can I just remove R10 completely leaving holes in the board?

I see a note on the drawing set that says I can remove R10 if the voltage is less than 4.75v but I'm getting 4.9v so, like you, I'm beginning to think it's not the PSU.

Any more ideas as to where the fault may lie?
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
I haven't read through the whole thread, but that's not a power supply problem. 4.9v or so is more than enough to power the board!!

Having said that, from what I did skim through I didn't notice you say WHERE you're measuring that 4.9v. Is that measured at one of the logic chips on the main CPU board? If so you power is fine and you have one or more PCB faults.

Martin.

guddler2013-11-24 13:43:47
 

R177

Newbie
Credits
11CR
I measured the 4.96v on the output from the PSU. I think I've just about exhausted my 'skills' and am now doubting my ability to fix this myself
smiley5.gif
.

Anyone in West or Central Scotland able to fix Robotrons?!
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
OK, measuring a voltage at the output of the power supply is no good whatsoever. Measure 5 volts by finding a 74 series logic chip on the main PCB (74LSnnn) and do GND on the bottom right pin, Positive on the top left pin. See what that reads and let us know.

It still sounds like a PCB fault or two to me though.
 

R177

Newbie
Credits
11CR
guddler said:
OK, measuring a voltage at the output of the power supply is no good whatsoever. Measure 5 volts by finding a 74 series logic chip on the main PCB (74LSnnn) and do GND on the bottom right pin, Positive on the top left pin. See what that reads and let us know.

It still sounds like a PCB fault or two to me though.

OK, I checked the chips you mentioned today and I'm only getting 4.88v there, is that enough?
 

R177

Newbie
Credits
11CR
OK I'm assuming 4.88v is not enough to run the boards so it could be a power issue after all but I've rebuilt the PSU as mentioned above.

Am I missing something somewhere? Should I give up and have someone who knows what they're doing have a look at my board set.

smiley18.gif
smiley5.gif
 
Top