Sega driver ventilation grills

Danscu

Active member
vacBacker
Feedback
10 (100%)
Credits
255CR
Hi

Had Muddymusic's Scud delivered yesterday, thanks again Olly!

There are what look like two ventilation grills (arrowed below) that are loose, which I want to put back in place.

Could anyone advise how best to access them and also which sort of glue or fixing I should use to hold them in place? They would need fixing in place securely due to the force feedback potentially popping them out of place again.

Thanks

Dan

scud_vent_grills.png
 

Outrun2

Colonel Outrun
Feedback
5 (100%)
Credits
1,182CR
These grilles originally had small tweeters behind them on Model 2 drivers like Daytona USA - there are brackets for them on the metal dash frame behind the plastic. Model 3 drivers never had these speakers installed, but that is an early Model 3 dash plastic which still had metal covers (probably has a more oval shaped boss for the steering wheel shaft to go through as well).

The newer dash plastics still have the grilles but they are part of the plastic moulding.

To get to them you will need to remove the complete dash assembly by removing the four security torx bolts - one in each corner of the dash (you might find three underneath as well). Pull the dash towards you 5-6 inches but be careful not to pull too hard as the dash will fall out and rip out the connectors tucked at the back. These dashes are very heavy as the motor on the left is a monster (total weight of dash assembly is around 23Kg - these things are built to last!)

Unplug all connectors behind the dash and remove the complete unit. You then have to remove the wheel emblem, wheel, shifter, shifter plastics, VR panel, denomi plate and three screws on the meter panel. Finally you can remove the main dash plastic and get to the grilles.

By the way, they probably won't fall out - they seem loose, but they are usually just secured 'loosely'.
 

Outrun2

Colonel Outrun
Feedback
5 (100%)
Credits
1,182CR
The one with the meters on
smiley2.gif


There will be three screws in the cowling behind the steering wheel - where the speedo/oil/water gauges are. Don't worry about the rivets - they don't need to come off.
 

Bods

Senior Member
vacBacker
Feedback
5 (100%)
Credits
5,414CR
The Speedo Dials matey, the surround metal has bolts through which hold dash too, also the window for price of play next to shifter has bolts through to metal behind dash

Some of the metal tweeter grills are melted in and some probably older screwed in but there often loose
 

obcd

Active member
Credits
3,830CR
They don't come loose due to the steering force feedback. They come loose because people push on them. (usually young kids) On some assemblies, they are just fixed by plastic pins that got melted to become thicker. Those studs break off rather easily. You can drill a small hole in the plastic and screw a heated parker into that hole to fix the grill. I usually heat the screw with the tip of my soldering iron till I see the plastic becoming weak (screw starts to wiggle in it's hole). You screw in the parker and wait a while for the plastic to harden again. After that, you can unscrew the parker screw and you have a perfect hole with thread that shouldn't break very easily anymore.

If you insert a cold parker screw directly, the plastic can split open.
obcd2017-05-17 16:43:40
 

obcd

Active member
Credits
3,830CR
A parker screrw is one of those with a thicker thread and a sharp point. It's a bit like a wood screw, but the screw head is flat instead of coned. They are often used as a quick dirty solution when screw holes became damaged so that the original screw doesn't fit anymore.

https://nl.wikipedia.org/wiki/Schroef_(verbinding)

On the picture with the 2 screws, the one on the left is a parker.
 
Top