Sega megatech screen issues

ukaccord

Newbie
Credits
4CR
Hi guys..not very clued on about arcade stuff so go easy on me please lol.. got a sega megatech which was working fine a couple of weeks ago.. turned it on today to find the picture has become funny.. I ger square blocks or vertical lines across the image :( tried readjusting the picture and cleaned contacts on carts on the pcb but still no joy. Any ideas on what it could be..monitor or pcb flat fault ?? Any help would be hugely appreciated for this newbie :) many thanks.
 

ukaccord

Newbie
Credits
4CR
http://s866.photobucket.com/user/ukaccord/media/Mobile%20Uploads/Screenshot_2015-10-30-23-15-22_zps4kj80tbu.png.html?filters[user]=108931604&filters[recent]=1&sort=1&o=0
 

ukaccord

Newbie
Credits
4CR
http://s866.photobucket.com/user/ukaccord/media/Mobile%20Uploads/Screenshot_2015-10-30-23-15-16_zpssa9mxlod.png.html?filters[user]=108931604&filters[recent]=1&sort=1&o=1
 

Alpha1

Do the Shake and 'VAC
Staff member
vacBacker
Feedback
95 (99%)
Credits
5,653CR
Check your +5, if it is fine and reseating the socketed chips doesn't help - people on here can repair the PCB for you.
 

ukaccord

Newbie
Credits
4CR
Thanks for the reply alpha.. tbh I have no idea were +5 is...sorry still noob at this still learning.. but will try and find it buddy :)ukaccord2015-10-31 13:37:25
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR
Mega-tech is a pretty annoying PCB as it's got it's own pin-out over about 7 or 8 different connectors. I've got one and it came with a faulty board; in the end i had to replace the board completely.

Power connector is the 14 pin connector on the left of the board (if memory serves me right):

http://wiki.arcadeotaku.com/w/Sega_Mega-Tech_Pinout

Try some simple things first:

- Pull out all carts and just put one back in slot 1; turn back on and see if the issue is still there

- try pressing all ICs into their sockets

- You can try reseating the ICs but do the above first
 

ukaccord

Newbie
Credits
4CR
Nes4life thanks for the tips buddy.. I took out the whole pcb and cleaned the pcb as it was dusty took out all the carts and looked for any roms which may have become loose or bad solder points. . Nothing seemed out of the ordinary but underneath there were quite a few jumper wires?? no idea what they are for but left them well alone.. plugged back in and on initial start up the picture was much better..I could see the car clear on out run.. but as I cycled through the games and came back to out run it all got scrabbled again :( so I took it all out and retried everything I did before ...nothing couldn't get close to the semi good picture I had before...so no idea..
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR
If on a cold boot the pic is good and then becomes garbled then it's possible that a capacitor or two have gone bad. Do nothing for a few hours boot it up and then see what happens. Don't cycle the games but just watch.

Those jumper wires are normal on the underside - poor design.Nes4life2015-10-31 22:57:38
 

ukaccord

Newbie
Credits
4CR
It was on the first run after I cleaned it all up buddy.. but after that I couldn't get it to give a perfect t picture on boot... sound and everything else is all good. . No weird noises.. just some of the image distorted or lines all over the place.
 

ukaccord

Newbie
Credits
4CR
Tbh I think I need to send this to some who knows what they are doing lol.. trains and cars no problem.. but thsee things I'm still learning lol...and there alot to learn lol.
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR
The truth is there's a whole group of us with varying issues with these boards. There's a common issue with the carts not being read but you've not got that so that's good. There's not many guys available who fix this type of board as it's actually closer to a console then an arcade machine. The second issue is that it has a custom harness so anyone fixing one will need to create a converter to jamma; which is a big ask. It's also crammed full of custom chips so most issues lead to these which are not readily replaceable. A different route might be to contact someone who repairs Megadrives and explain the issue as they might know what to replace.

I've seen Mega-tech's converted to hyperspin (with a PC inside) and running only Sega games. That's not a bad choice as the top screen can still be used to display marquees etc.

Hope you find someone but if you don't you might need to use this as a way to learn more about fixing PCBs and do it yourself or have a conversion project on your hands.
 

ukaccord

Newbie
Credits
4CR
Many thanks for the kind reply Nes4life. I agree with everything you have said. It would be brilliant to get this working and keeping it original as possible. But it's getting hard finding good info on it and alot of the info I find is Usally translated from another language so it's hard to grasp what's going on through translation. I saw the hyperspin conversion on another forum and they guy done a superb build even replacing the top to a 10" lcd screen and having the games show up on there while running the bottom. I remember his mentioning that he wanted to keep it as original as possible and left the 3 buttons..i would a let up like that but at the moment it's a big decision as I wanted to keep it as original as possible...
 

ukaccord

Newbie
Credits
4CR
Iirc the guy who done the awsome work was called zeebow ...does Andy still make the cpo for the megatech..last I heard he had moved to the states???
 

Nes4life

Active member
vacBacker
Feedback
12 (100%)
Credits
1,134CR
You can get a new CPO printed via muddymusic. I gave him updated dimensions and positions of buttons etc when I had mine printed. I've also got the adapter that allows you to use 6 button MegaDrive controllers with it.
 
Top