SI Sound Issues

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
OK, I have a Jap Taito L-Shape set on the bench at the moment and it's starting to do my head in !

I've fixed the CPU board and got the game running. It had the usual missing sounds so after I probed about about I worked out that all the sounds involving "NOISE" were missing so I started the hunt for a 4006. After about a month I finally have one of those and all the NOISE sounds have come back but with a twist.

I now have white noise from the moment you start play to the moment you lose your last life and I can't really make out what's causing that. The outputs from the 74LS174's that switch the sounds on and off are doing their thing quite nicely. I've tested all 1N4148 diodes and they seem to be OK.

I have a bit of a suspicion it could be the 74LS17 that buffers / isolates the on/off signal for the sounds, but I have to say, it looks good on the scope.

And this is where it does my head in. I don't normally work on SI boards so not only did I not have any 4006's, I now find I don't have any 74LS17
smiley36.gif


Before I go searching for some of those to substitute, anyone else know these boards better than me can tell me if anything else might be causing this?

I'm really hoping I'm looking in the wrong place.

Ta.
 

PaulSwan

ZZZ
Feedback
1 (100%)
Credits
1,118CR
IIRC the reason you have this effect during the game is that there is a global mute that's muting the final pre-amp when no game is in play. Often this is a bad op-amp/sound circuit in one of the sounds that's throwing out noise all the time or the pre-amp circuit itself has a fault. You should be able to use a scope or crystal earpiece to hunt the source.

Paul.
 

andrewsm

Active member
Feedback
1 (100%)
Credits
485CR
Funnily enough I noticed same problem with my moonbase. Noise was gone as well as other sounds. Got them all going but as soon as the game starts, there is a slightly higher background noise than when is the attract screen. Not bothered to really do much about it yet but sounds similar. Also getting a hum which at low volume can be quite noticable. I know the 12v has some ripple but as yet not cured it. Games runs great and after a while you get used to it.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Ah, this is different to that. The noise is an intended game noise. The noise you get when your base is shot and you lose a life. But it's on constant!

@Paul: I don't mind admitting, I'm not all that clued up on this! Can the LM3900's act like a switch and therefore go faulty and get stuck in a state that would mean the sound is constantly on?

I had pretty much ignore the op-amps because I thought they were purely for amplification but it sounds like I might be wrong.

I had assumed...

Inputs come from motherboard as data signals to port 2 or port 3. The 74LS174's turn these signals into on/off switches (basically) and the 74LS17(s) act as a buffer between the TTL (5v) and CMOS (12v) logic levels. So this is why I was assuming that a sound which is stuck on all the time must be related to one of those two and since I don't have any 74LS17's I was guessing those. BUT, the signals look fine.

So should I look at the LM3900's then? I know they are renowned for being the culprit of a missing sound, but a sound being permanently on???
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Cocktails specifically I couldn't say but in general yes, it's not uncommon. Check that you have good ground connections everywhere. Also on SI you might notice it more because the sound is being cut off completely until the game starts.
 

andrewsm

Active member
Feedback
1 (100%)
Credits
485CR
ah ok. Well I do know the psu is not the best tbh as just a refined full wave type and the hum is just a low level 50hz one. Prob is an arcade or bar then surrounding noise would drown it out but in a quiet lounge its more noticable. I have grounded everything and the boards are pretty much 100% but just wondered before I tear my hair out chasing a problem that will never go.

Cheers

Mark
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
OK, I need help (I know, I know!) I'm getting nowhere with this!

I've socketed and replaced all LM3900's. All sound effects are now present except for UFO Hit. I think that is one of the 74LS17's but I don't have any, I'll see if I can order one in. I've verified that the 74LS174's and the 7411 are correct.

And still I have this damn persistent explosion sound.

I haven't replaced the final LM377 (from memory) op-amp as I'm not convinced I'll get it out without wrecking something, I also don't know if I have any. It seems to be fairly well welded to two large blades of metal as heat sinks. It could be that I suppose.

So that leaves a myriad of small analogue components such as resistors, caps etc., none of which are labelled up with component numbers.

DOES ANYONE UNDERSTAND THIS CIRCUIT and can tell me where to look please before I send it back as "cannot fix" ???

Thanks.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Honestly no idea - this is the only SI board I've ever got into. I always normally stay away from them
smiley36.gif


I know it's the same basic principal because the 3 layer set still has all the individual volume pots but as to whether the rest of the circuit is the same??
 

pobtastic

Moderator
Staff member
vacBacker
Feedback
2 (100%)
Credits
477CR
Check out the 104K mylar caps, or even the resistors ~ that said, the odd part is that the sound isn't "stuck on" it's dependant on certain (reproducible) factors... My instinct says that it's a decoder problem, but even then it's actually switching in some points so it's possibly even further up the chain?

It's certainly an interesting one!
pobtastic2016-03-20 11:13:07
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
This board doesn't want to give in easily!!!

SO, fixed the explosion being stuck on all the time. It was a 4.7M Ohm resistor that had gone open. It's basically a +12v pull-up. Open = sound on, closed = sound off. I tried a 1M resistor as it was the closest I had and that was too little as it was then permanently off. Ordered in some 4.7M resistors and bingo. Explosion only when you die.

Which brings me to what I HOPE is the last damn fault with this thing. No UFO hit noise. SX10 is being generated OK out of the LS174 @ 1. I can trigger it manually by jumping pin 2 @ 16 to +5v, but the input of the OC buffer (pin 1 @ 16) cannot be made to go high. So it looks like this last one is the 7417N @ 16.

Another chip I don't have any of !!!

Further eBay order placed. I will be glad to give this board back to it's owner. Hopefully at the weekend.
 

RGP

Meeter & Greeter
Feedback
5 (100%)
Credits
2,039CR
Wow, sorry you've had so much pain with this one Martin, i'm glad you've found it in the end, I have an SIpt2 with missing sounds to look at for Andy at some point, i'm just hoping its not this bad.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Hi Nad. Thankfully I don't think there's any need, the UFO hit sound works perfectly when I trigger it manually, it's just the trigger is being held low going into the 7417. Least that's what I think it is, anyway!

@James. Analog is not my friend. I've always known it. Space Invaders is just backing it up. I won't touch another after this for sure.
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
Oh, PS: the 76477 generates the UFO movement sound. Admittedly the hit sound is just like a slower version so I suppose it may do them both? If so, yeah, I'll check it. I don't have any 7417's so 10 for £4 delivered won't be a waste anyway...

Pretty sure I HAVE seen a 76477 in my random chip section. Very few have that fine pitch
 

guddler

Busting vectors like it's 1982!
vacBacker
Feedback
10 (100%)
Credits
4,058CR
FINALLY wrapped this one up tonight! The last fault was the missing UFO hit sound which did indeed turn out to be a duff input gate on one of the 7417N's. Shame they took an entire week to arrive from the UK.

A little bit of a naff video - I'm a liability with YouTube so I've no idea why it's managed to turn a nice 1080p@60 video into a 480p affair, but never mind, you get the idea. Take my word for it that the extra life sound also works, but there was no way I was going to get that far with only one hand...


guddler2016-04-12 23:11:06
 

andrew96

Unfixable? What's that word mean?
Feedback
1 (100%)
Credits
899CR
good work! well done!

The best way I found to tackle sound was to put a braze multigame board in place of the cpu and you have a test menu where you can access all the sounds to test one by one which is very handy!
 
Top