Sinistar power board problem

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
My Sinistar has a switcher fitted and the game runs 100%, no issues so i am certain i dont have a board problem.

In an effort to get the cabinet back to 'stock' I have tried my very first ever repair - the non-working origional power board.

I got the components that i think were needed and proceeded to desolder the old ones, and fit new ones. I was unfortunately unable to get the Bridge Rectifier BR2 out so that is still original. I have plugged the board back in and get the following voltages at the test points on the power board

TP1 - +5V reg; +4.95

TP2 - GND

TP3 - +12V reg; +12.25V

TP4 - -5V; -4.99V

TP5 - +12V reg; +12.18V

TP6 - -12V unReg; -12.48V

The coin door switches etc work fine but when i plug the main loom into the power board i get a 'rug' pattern on the screen - not the same as the standard Williams boot-up screen, this is more 'organised' if you know what i mean.

Having tested the voltages i am very disappointed that it doesnt now work, anyone got any tips on what to do next?
 

philmurr

Active member
vacBacker
Feedback
48 (100%)
Credits
2,374CR
Values look ok at the PSU...but can you recheck them on the Sinistar PCB itself (or on the connector where it plugs into the PCB) and let us know the results ?
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
Last time i did that i blew a fuse
smiley9.gif


ill try the pcb in a bit...
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
Just did a quick check on the connector as it goes into the main pcb

+12V reg = 11.85V

+5V - 4.77V

+12V unreg = 9.06V

-5V = 5V

the behavior has changed - i now no longer get the rug pattern, the game boots and plays ok but there is no sound - i guess the voltages are just far enough out to cause this problem (I replugged the switcher back in just to check and i get the sound ok)

chubsta2013-09-10 16:32:29
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Sound board needs -12VDC. So you need to check that too. But check the voltages on the sound board itself. Same process as you did on power board - but on sound board as follows:

TP1: +12
TP2: -12
TP3: GND
TP4: +5

Have a go at that using the linear supply rather than switcher and then report back. Good luck!

Out of interest, which fuse did you manage to blow?tb lilley2013-09-10 18:09:18
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
I'm all p*ssed up on Ace at the moment
smiley4.gif
smiley9.gif


8-Ace.jpg


so have decided not to try messing with electrics, but the fuses were F4 and F5, i have replaced them. Ill check the voltages on the soundboard in the morning - some of the ones going into the main board seem low so to me that is the obvious problem but what do i know
smiley9.gif
 

tb lilley

5 Star
vacBacker
Feedback
2 (100%)
Credits
1,686CR
Yeah - fuses F4 and F5 protect the bridge rectifier at BR1. BR1 is supposed to kick out the -12 the sound board requires. So it's possible you've a problem in or around that area.

When your off the Ace recheck TP6 on the power board, and also TP2 on the sound board. BR1 does a lot more than the -12 though, so I'd presume its ok. Dunno - but yeah, check voltages on sound board. Unusual for power board to output correct voltages and for them to not show up on sound board - particularly when all is well and good when using switcher.

Enjoy the Ace.
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
i changed BR1 so i cant see an issue with that, its weird though how the problem has progressed - to start with i got the rug pattern, then for a few reboots it went to booting with graphics problems, then it works fine for graphics but there is no sound.

the joys of a dedicated cabinet
smiley18.gif
 

chubsta

Active member
Feedback
4 (100%)
Credits
547CR
Of course, i could just leave the switcher in there and play the game with no problems and no stress...

What is it about these things that we have to work on them and stress until they are 'right'?

My other half thinks I'm an idiot, I may have just had an epiphany and think she is right...
 

philmurr

Active member
vacBacker
Feedback
48 (100%)
Credits
2,374CR
Voltage levels look in spec but I've had problems in the past with the +5V being 4.80V at the board. I ran new wiring and new crimps to fix it - may be worth removing the connectors and cleaning the pins both ends ?

Or yes, stick with the switcher...
 
Top